Page 1 of 1
Scanner funktioniert nur als root. Brauche Userzugriff.
Posted: 24. Oct 2007 22:06
by sesame
Hallo,
der CanoScan N670U (USB) wird perfekt unter root erkannt
(
http://www.sane-project.org/man/sane-plustek.5.html).
Starte ich sane bzw. xsane als user, sind keine Geräte erreichbar.
Wie kann ich unter Debian einen Userzugriff einrichten?
Posted: 25. Oct 2007 8:07
by Janka
Zwei Möglichkeiten:
1. USB-Devicenode auch für den Benutzer freigeben -- erfordert etwas Handarbeit bei udev
2. saned einrichten wie für Parallelportscanner beschrieben (da geht es nur so.)
Ich erklär mal 2., weil ich das auch so gemacht habe.
In /etc/sane.d/dll.conf das Kommentarzeichen beim Eintrag
entfernen.
In /etc/sane.d/net.conf die folgende Zeile hinzufügen
In /etc/sane.d/saned.conf die folgenden Zeilen hinzufügen
Nachprüfen, dass es in /etc/services den Eintrag
Code: Select all
sane-port 6566/tcp # SANE Control Port
gibt. Wenn nicht, hinzufügen.
Im Verzeichnis /etc/xinetd.d eine Datei mit dem Namen sane-port anlegen und folgenden Inhalt reinschreiben:
Code: Select all
service sane-port
{
socket_type = stream
port = 6566
wait = no
user = root
group = root
server = /usr/sbin/saned
disable = no
}
Wenn es /etc/xinetd.d nicht gibt, direkt rein in /etc/xinetd.conf damit
Danach xinetd die Konfigurationsdateien neu lesen lassen:
Jetzt können alle lokalen Benutzer auf den Scanner via saned zugreifen.
Janka
Posted: 25. Oct 2007 11:32
by sesame
Danke für die schnelle Antwort.
Habe jetzt alles so nach Anleitung gemacht, bekomme aber als user immer noch keinen Zugriff.
Dann scanne ich erst einmal als root weiter.
Wenn jemand noch eine Idee hat, möge sie hier posten.
Posted: 25. Oct 2007 14:21
by Janka
Wenn du es genau nach dieser Anleitung gemacht hast, muss es auch funzen. Du brauchst keine andere Idee, sondern musst den Fehler suchen.
Kannst ja erstmal gucken, ob bei dir überhaupt xinetd läuft. Wenn nicht, starten. /etc/init.d/xinetd start.
Außerdem kannst du auch nachschauen, ob der saned tatsächlich unter /usr/sbin/saned liegt. Bei mir ist das der Fall, muss aber bei dir nicht zwangsläufig auch so sein.
Was liefert "scanimage -L", als Benutzer ausgeführt, zurück?
Janka
Posted: 25. Oct 2007 16:45
by sesame
Der Befehl "scanimage -L" liefert als user
Code: Select all
No scanners were identified. If you were expecting something different,
check that the scanner is plugged in, turned on and detected by the
sane-find-scanner tool (if appropriate). Please read the documentation
which came with this software (README, FAQ, manpages).
und als root:
Code: Select all
device `plustek:libusb:001:006' is a Canon CanoScan N670U/N676U/LiDE20 flatbed scanner
zurück.
xinetd läuft und saned ist in /usr/sbin/saned vorhanden.
da kann ich dann nur irgendwas falsch gemacht haben?
ich werde den grund finden und dann posten.
danke für die hilfe.
Posted: 25. Oct 2007 21:56
by Janka
Evtl. sperrt eine Firewall-Regel den saned-port? Kannst du saned z.B. per telnet erreichen?
Code: Select all
$ telnet localhost sane-port
Trying 127.0.0.1...
Connected to localhost.
Escape character is '^]'.
Janka
Posted: 26. Oct 2007 10:50
by sesame
Jetzt geht's!
habe nochmal alles das gemacht, was ich nun auf
https://lists.uni-koeln.de/pipermail/li ... 11729.html
gefunden habe:
Code: Select all
So wird nun vorgegangen um saned zu verwenden und das Scannen (PP-Scanner)
auch den Usern zu ermöglichen:
1. saned als root laufen lassen
(ggf. /etc/xinetd.d/sane-port, /etc/xinetd.d/saned o.ä„. anpassen).
# /etc/xinetd.d/saned
# default: off
# description: The sane server accepts requests
# for network access to a local scanner via the
# network.
service sane-port
{
port = 6566
socket_type = stream
wait = no
user = root
group = saned
server = /usr/sbin/saned
}
2. In /etc/sane.d/saned.conf den Zugriff von "localhost" erlauben.
# /etc/sane.d/saned.conf
#
# The contents of the saned.conf file is a list of host names, IP
# addresses or IP subnets (CIDR notation) that are permitted to use local
# SANE devices. IPv6 addresses must be enclosed in brackets, and should
# always be specified in their compressed form.
#
# The hostname matching is not case-sensitive.
#
#scan-client.somedomain.firm
#192.168.0.1
#192.168.0.1/29
#[2001:7a8:185e::42:12]
#[2001:7a8:185e::42:12]/64
#
# NOTE: /etc/inetd.conf (or /etc/xinetd.conf) and
# /etc/services must also be properly configured to start
# the saned daemon as documented in saned(8), services(4)
# and inetd.conf(4) (or xinetd.conf(5)).
#
localhost
3. In /etc/sane.d/net.conf "localhost" als Server eintragen.
# This is the net config file. Each line names a host to attach to.
# If you list "localhost" then your backends can be accessed either
# directly or through the net backend. Going through the net backend
# may be necessary to access devices that need special privileges.
localhost
4. In /etc/sane.d/dll.conf das "net" Backend aktivieren.
Posted: 26. Oct 2007 10:51
by sesame
Jetzt geht's!
habe nochmal alles das gemacht, was ich nun auf
https://lists.uni-koeln.de/pipermail/li ... 11729.html
gefunden habe:
Code: Select all
So wird nun vorgegangen um saned zu verwenden und das Scannen (PP-Scanner)
auch den Usern zu ermöglichen:
1. saned als root laufen lassen
(ggf. /etc/xinetd.d/sane-port, /etc/xinetd.d/saned o.ä„. anpassen).
# /etc/xinetd.d/saned
# default: off
# description: The sane server accepts requests
# for network access to a local scanner via the
# network.
service sane-port
{
port = 6566
socket_type = stream
wait = no
user = root
group = saned
server = /usr/sbin/saned
}
2. In /etc/sane.d/saned.conf den Zugriff von "localhost" erlauben.
# /etc/sane.d/saned.conf
#
# The contents of the saned.conf file is a list of host names, IP
# addresses or IP subnets (CIDR notation) that are permitted to use local
# SANE devices. IPv6 addresses must be enclosed in brackets, and should
# always be specified in their compressed form.
#
# The hostname matching is not case-sensitive.
#
#scan-client.somedomain.firm
#192.168.0.1
#192.168.0.1/29
#[2001:7a8:185e::42:12]
#[2001:7a8:185e::42:12]/64
#
# NOTE: /etc/inetd.conf (or /etc/xinetd.conf) and
# /etc/services must also be properly configured to start
# the saned daemon as documented in saned(8), services(4)
# and inetd.conf(4) (or xinetd.conf(5)).
#
localhost
3. In /etc/sane.d/net.conf "localhost" als Server eintragen.
# This is the net config file. Each line names a host to attach to.
# If you list "localhost" then your backends can be accessed either
# directly or through the net backend. Going through the net backend
# may be necessary to access devices that need special privileges.
localhost
4. In /etc/sane.d/dll.conf das "net" Backend aktivieren.
Einiges hatte ich schon erledigt. Aber nun geht es
Vielen Dank nochmal.