Die Tastatur ist auch blokiert. Es hilft nur die Resettaste ;-(
Die letzte Kernel Meldung sieht so aus:
Seting up /etc/ld.so.cachehdc: timeout wating for DMA
Wo kann die Ursache liegen, wie kann ich das lösen?
Was wird noch nötig für Lösung dieses Prroblems?
Danke für jejde Hilfe und Hinweis
Pawel
Mein fstab sieht so aus:
/dev/hda5 swap swap defaults 0 0
/dev/hda6 / ext2 defaults 1 1
/dev/hdc3 /usr ext2 defaults 1 2
/dev/hdc6 /var ext2 defaults 1 2
/dev/hdc5 /boot ext2 defaults 1 2
/dev/hda8 /home ext2 defaults 1 2
/dev/hdc2 /test_root ext2 defaults 1 2
/dev/hdc1 /archiv ext2 defaults 0 2
/dev/hdc7 /test_usr ext2 defaults 1 2
/dev/hda7 /usr/lib ext2 defaults 1 2
/var/log/boot.msg sieht so aus:
========Auszug=============
<4>PIIX4: IDE controller on PCI bus 00 dev 39
<4>PIIX4: not 100% native mode: will probe irqs later
<4> ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio
<4> ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
<4>hda: ST34321A, ATA DISK drive
<4>hdb: TOSHIBA CD-ROM XM-6102B, ATAPI CDROM drive
<4>hdc: QUANTUM FIREBALL ST3.2A, ATA DISK drive
<4>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
<4>ide1 at 0x170-0x177,0x376 on irq 15
<6>hda: ST34321A, 4103MB w/128kB Cache, CHS=523/255/63, UDMA
<6>hdc: QUANTUM FIREBALL ST3.2A, 3079MB w/81kB Cache, CHS=6256/16/63, UDMA
<6>sym53c8xx: at PCI bus 0, device 12, function 0
<4>sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
<6>sym53c8xx: 53c860 detected with Symbios NVRAM
<6>sym53c860-0: rev=0x02, base=0xe4000000, io_port=0x6400, irq=11
<6>sym53c860-0: Symbios format NVRAM, ID 7, Fast-20, Parity Checking
<6>sym53c860-0: initial SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 05/8e/a0/01/00/00
<6>sym53c860-0: final SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 05/ce/a0/00/08/00
<4>sym53c860-0: resetting, command processing suspended for 2 seconds
<6>sym53c860-0: restart (scsi reset).
<4>scsi0 : sym53c8xx - version 1.3c
<4>scsi1 : SCSI host adapter emulation for IDE ATAPI devices
<4>scsi : 2 hosts.
<4>sym53c860-0: command processing resumed
<4> Vendor: YAMAHA Model: CRW8424S Rev: 1.0d
<4> Type: CD-ROM ANSI SCSI revision: 02
<4>Detected scsi CD-ROM sr0 at scsi0, channel 0, id 1, lun 0
<4> Vendor: TOSHIBA Model: CD-ROM XM-6102B Rev: 1106
<4> Type: CD-ROM ANSI SCSI revision: 02
<4>Detected scsi CD-ROM sr1 at scsi1, channel 0, id 0, lun 0
<4>scsi : detected 2 SCSI cdroms total.
<6>sym53c860-0-<1,*>: FAST-20 SCSI 20.0 MB/s (50 ns, offset
<4>sr0: scsi3-mmc drive: 24x/16x writer cd/rw xa/form2 cdda tray
<6>Uniform CDROM driver Revision: 2.55
<4>sr1: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray
<6>PPP: version 2.3.7 (demand dialling)
<6>TCP compression code copyright 1989 Regents of the University of California
<6>PPP line discipline registered.
<4>Partition check:
<4> hda: hda1 hda2 < hda5 hda6 hda7 hda8 >
<4> hdc: [PTBL] [782/128/63] hdc1 hdc2 hdc3 hdc4 < hdc5 hdc6 hdc7 >
<4>VFS: Mounted root (ext2 filesystem) readonly.
<4>Freeing unused kernel memory: 48k freed
<6>Adding Swap: 104380k swap-space (priority -1)
<4>hdc: timeout waiting for DMA
<4>hdc: irq timeout: status=0xd0 { Busy }
<4>hdc: DMA disabled
<4>ide1: reset: success
<4>EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
Kernel logging (proc) stopped.
Kernel log daemon terminating.
