Code: Select all
Luna root # hdparm -d 1 /dev/hda
/dev/hda:
setting using_dma to 1 (on)
HDIO_SET_DMA failed: Operation not permitted
using_dma = 0 (off)
Ich arbeite mit Gentoo Linux 2004.2 Kernel 2.6.7. DMA müsste einkompiliert worden sein:
Code: Select all
Luna root # grep DMA /boot/config-2.6.7-gentoo-r11
CONFIG_GENERIC_ISA_DMA=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
CONFIG_BLK_DEV_ADMA=y
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
CONFIG_IDEDMA_AUTO=y
Code: Select all
Luna root # hdparm -I /dev/hda
/dev/hda:
ATA device, with non-removable media
Model Number: Maxtor 4D060H3
Serial Number: D30ET7VE
Firmware Revision: DAH017K0
Standards:
Used: ATA/ATAPI-6 T13 1410D revision 0
Supported: 6 5 4 3
Configuration:
Logical max current
cylinders 16383 4047
heads 16 16
sectors/track 63 255
--
CHS current addressable sectors: 16511760
LBA user addressable sectors: 120069936
device size with M = 1024*1024: 58627 MBytes
device size with M = 1000*1000: 61475 MBytes (61 GB)
Capabilities:
LBA, IORDY(can be disabled)
bytes avail on r/w long: 57 Queue depth: 1
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Advanced power management level: unknown setting (0x0000)
Recommended acoustic management value: 192, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* NOP cmd
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
* Look-ahead
* Write cache
* Power Management feature set
* SMART feature set
* Device Configuration Overlay feature set
* Automatic Acoustic Management feature set
SET MAX security extension
Advanced Power Management feature set
* DOWNLOAD MICROCODE cmd
* SMART self-test
* SMART error logging
HW reset results:
CBLID- above Vih
Device num = 0 determined by the jumper
Checksum: correct
Luna root # hdparm -I /dev/hdb
/dev/hdb:
ATA device, with non-removable media
Model Number: Maxtor 6Y160P0
Serial Number: Y452B7BE
Firmware Revision: YAR41BW0
Standards:
Supported: 7 6 5 4
Likely used: 7
Configuration:
Logical max current
cylinders 16383 64761
heads 16 1
sectors/track 63 255
--
CHS current addressable sectors: 16514055
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 320173056
device size with M = 1024*1024: 156334 MBytes
device size with M = 1000*1000: 163928 MBytes (163 GB)
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 1
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Advanced power management level: unknown setting (0x0000)
Recommended acoustic management value: 192, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5 udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* NOP cmd
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
* Look-ahead
* Write cache
* Power Management feature set
Security Mode feature set
* SMART feature set
* FLUSH CACHE EXT command
* Mandatory FLUSH CACHE command
* Device Configuration Overlay feature set
* 48-bit Address feature set
* Automatic Acoustic Management feature set
SET MAX security extension
Advanced Power Management feature set
* DOWNLOAD MICROCODE cmd
* SMART self-test
* SMART error logging
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
HW reset results:
CBLID- above Vih
Device num = 1 determined by the jumper
Checksum: correct
Hat jemand Tipps?