suche Installationsanleitung für Skystar2 rev2.7

Post Reply
Message
Author
tux01

suche Installationsanleitung für Skystar2 rev2.7

#1 Post by tux01 »

Hallo

suche Installationsanleitung für Skystar2 rev2.7 für Kernel 2.6.28 (sidux).
Kaffeine erkennt die Karte, findet aber keine Kanäle.

Auszug aus dmesg:

Code: Select all

b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully
flexcop-pci: will use the HW PID filter.
flexcop-pci: card revision 2
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
b2c2_flexcop_pci 0000:01:06.0: PCI INT A -> Link[APC1] -> GSI 16 (level, low) -> IRQ 16
DVB: registering new adapter (FlexCop Digital TV device) 
http://linuxtv.org/hg/~pb/v4l-dvb/archi ... 3b.tar.bz2 ließ sich bei mir nicht compilieren (Fehler 2).

Code: Select all

Kernel build directory is /lib/modules/2.6.28-2.slh.2-sidux-686/build
make -C /lib/modules/2.6.28-2.slh.2-sidux-686/build SUBDIRS=/home/tux/v4l-dvb-ece80295453b/v4l  modules
make[2]: Entering directory `/usr/src/linux-headers-2.6.28-2.slh.2-sidux-686'
  CC [M]  /home/tux/v4l-dvb-ece80295453b/v4l/cxusb.o
/home/tux/v4l-dvb-ece80295453b/v4l/cxusb.c: In function 'bluebird_patch_dvico_firmware_download':
/home/tux/v4l-dvb-ece80295453b/v4l/cxusb.c:705: error: assignment of read-only location '*(fw->data + ((unsigned int)idoff + 2u))'
/home/tux/v4l-dvb-ece80295453b/v4l/cxusb.c:707: error: assignment of read-only location '*(fw->data + ((unsigned int)idoff + 3u))'
make[3]: *** [/home/tux/v4l-dvb-ece80295453b/v4l/cxusb.o] Error 1
make[2]: *** [_module_/home/tux/v4l-dvb-ece80295453b/v4l] Error 2
make[2]: Leaving directory `/usr/src/linux-headers-2.6.28-2.slh.2-sidux-686'
make[1]: *** [default] Fehler 2
make[1]: Leaving directory `/home/tux/v4l-dvb-ece80295453b/v4l'
make: *** [all] Fehler 2 

User avatar
Janka
Posts: 3585
Joined: 11. Feb 2006 19:10

Re: suche Installationsanleitung für Skystar2 rev2.7

#2 Post by Janka »

tux01 wrote:Suche Installationsanleitung für Skystar2 rev2.7 für Kernel 2.6.28 (sidux).
Kaffeine erkennt die Karte, findet aber keine Kanäle.

Auszug aus dmesg:

Code: Select all

b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully
flexcop-pci: will use the HW PID filter.
flexcop-pci: card revision 2
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
b2c2_flexcop_pci 0000:01:06.0: PCI INT A -> Link[APC1] -> GSI 16 (level, low) -> IRQ 16
DVB: registering new adapter (FlexCop Digital TV device) 
Die Karte wurde erkannt und der in Linux-2.6.28 enthaltene Treiber ist auch ganz bestimmt funktionsfähig, der ist da nämlich schon länger drin. Das Problem ist vermutlich bei Kaffeine bzw. der Xine-Engine dahinter zu suchen. Evtl. fehlt auch einfach die libdvbpsi zum Dekodieren des DVB-Streams?

Im VDR-Portal wirst du sicher Leute finden, die auch diese Karte haben und dir direkt berichten können.
http://www.vdrportal.de/board/portal.php

Janka
Ich vertonne Spam immer in /dev/dsp statt /dev/null.
Ich mag die Schreie.

Post Reply