S-Video mit Opensuse 11.1 und Mainborad D945GCLF2

Message
Author
inixlinux

S-Video mit Opensuse 11.1 und Mainborad D945GCLF2

#1 Post by inixlinux »

Hallo,

ich hätte gerne das Bild meines Rechners über S-Video am TV ausgegeben.

Wenn ich mit Sax2 einen 2Monitor einrichten erhalte ich nun zwar ein Bild, jedoch "rollt" dieses.

An was kann das liegen?

Ich habe bereits verschiedene Einstellungen bezüglich der Synchronisierung getestet, jedoch erhalte ich jedesmal das rollende Bild.

Graka ist die 945G von Intel mit dem Mesa Treiber 7.2

Danke

User avatar
Janka
Posts: 3585
Joined: 11. Feb 2006 19:10

#2 Post by Janka »

Ein Ferni ist ein Festfrequenzmonitor. Die Timingwerte müssen für einen Ferni ziemlich genau eingehalten werden. Der zweite Ausgang der Grafikkarte muss mit einer Horizontalfrequenz von 15625 Hz betrieben werden, die Framerate muss bei 50 Hz liegen. Viele Fernis schlucken auch bis 60Hz. Die beiden Sync-Polaritäten müssen jeweils auf Negativ eingestellt sein, und das Bild sollte mit Interlace ausgegeben werden.

Vermutlich stellt Sax2 die Sync-Polarität nicht richtig ein, evtl. passt auch die Vertikalfrequenz nicht ganz. Dann rollt das Bild. Wenn es gar nicht klappt, kannst du Modelines verwenden, da kann man alle Timingparameter genau angeben. Ein paar Beispiel-Modelines:

Code: Select all

Section "Monitor"
  HorizSync    15-16
  Identifier   "TV""
  VertRefresh  49.0-61.0
  UseModes     "Modes[TV]"
EndSection

Section "Modes"
  Identifier   "Modes[TV]"
  Modeline "ntsc_320x240" 6.04186 320 328 352 384 240 244 247 262 -hsync -vsync # H 15734 [Hz], V 60.0534 [Hz]
  Modeline "ntsc_400x300" 7.55232 400 408 448 480 300 398 404 525 -hsync -vsync interlace # H 15734 [Hz], V 59.939 [Hz]
  Modeline "ntsc_512x384" 9.69214 512 528 568 616 384 440 446 525 -hsync -vsync interlace # H 15734 [Hz], V 59.939 [Hz]
  Modeline "ntsc_640x480" 12.2096 640 664 720 776 480 488 494 525 -hsync -vsync interlace # H 15734 [Hz], V 59.939 [Hz]
  Modeline "ntsc_720x480" 13.72 720 744 808 872 480 488 494 525 -hsync -vsync interlace # H 15734 [Hz], V 59.939 [Hz]
  Modeline "ntsc_720x480jk" 13.72 720 744 778 872 480 488 494 525 +hsync +vsync interlace # H 15734 [Hz], V 59.939 [Hz]

  Modeline "ntsc_320x242" 6.04186 320 328 352 384 242 245 248 262 -hsync -vsync # H 15734 [Hz], V 60.0534 [Hz]
  Modeline "ntsc_640x484" 12.0837 640 656 704 768 484 490 496 525 -hsync -vsync interlace # H 15734 [Hz], V 59.939 [Hz]

  Modeline "pal_320x240" 6.125 320 328 360 392 240 267 270 312 -hsync -vsync # H 15625 [Hz], V 50.0801 [Hz]
  Modeline "pal_400x300" 7.75 400 416 456 496 300 444 450 625 -hsync -vsync interlace # H 15625 [Hz], V 50 [Hz]
  Modeline "pal_512x384" 9.875 512 528 576 632 384 486 492 625 -hsync -vsync interlace # H 15625 [Hz], V 50 [Hz]
  Modeline "pal_640x480" 12.25 640 656 712 784 480 534 540 625 -hsync -vsync interlace # H 15625 [Hz], V 50 [Hz]

  Modeline "pal_768x576" 14.75 768 784 864 944 576 582 588 625 -hsync -vsync interlace # H 15625 [Hz], V 50 [Hz]
  Modeline "pal_720x576" 13.875 720 744 808 888 576 582 588 625 -hsync -vsync interlace # H 15625 [Hz], V 50 [Hz]
EndSection
Ich benutze diese Einträge in meiner /etc/X11/xorg.conf zusammen mit einem selbstgebastelten VGA->RGB-Kabel an einer ganz gewöhnlichen uralt-VGA-Karte, das klappt problemlos.

Janka
Ich vertonne Spam immer in /dev/dsp statt /dev/null.
Ich mag die Schreie.

inixlinux

#3 Post by inixlinux »

Meine /etc/X11/xorg.config

Code: Select all

# /.../
# SaX generated X11 config file
# Created on: 2010-01-18T18:39:42+0100.
#
# Version: 8.1
# Contact&#58; Marcus Schaefer <sax@suse.de>, 2005
# Contact&#58; SaX-User list <https&#58;//lists.berlios.de/mailman/listinfo/sax-users>
#
# Automatically generated by &#91;ISaX&#93; &#40;8.1&#41;
# PLEASE DO NOT EDIT THIS FILE!
#
Section "Files"
  FontPath     "/usr/share/fonts/misc&#58;unscaled"
  FontPath     "/usr/share/fonts/local"
  FontPath     "/usr/share/fonts/75dpi&#58;unscaled"
  FontPath     "/usr/share/fonts/100dpi&#58;unscaled"
  FontPath     "/usr/share/fonts/Type1"
  FontPath     "/usr/share/fonts/URW"
  FontPath     "/usr/share/fonts/Speedo"
  FontPath     "/usr/share/fonts/PEX"
  FontPath     "/usr/share/fonts/cyrillic"
  FontPath     "/usr/share/fonts/latin2/misc&#58;unscaled"
  FontPath     "/usr/share/fonts/latin2/75dpi&#58;unscaled"
  FontPath     "/usr/share/fonts/latin2/100dpi&#58;unscaled"
  FontPath     "/usr/share/fonts/latin2/Type1"
  FontPath     "/usr/share/fonts/latin7/75dpi&#58;unscaled"
  FontPath     "/usr/share/fonts/baekmuk&#58;unscaled"
  FontPath     "/usr/share/fonts/japanese&#58;unscaled"
  FontPath     "/usr/share/fonts/kwintv"
  FontPath     "/usr/share/fonts/truetype"
  FontPath     "/usr/share/fonts/uni&#58;unscaled"
  FontPath     "/usr/share/fonts/CID"
  FontPath     "/usr/share/fonts/ucs/misc&#58;unscaled"
  FontPath     "/usr/share/fonts/ucs/75dpi&#58;unscaled"
  FontPath     "/usr/share/fonts/ucs/100dpi&#58;unscaled"
  FontPath     "/usr/share/fonts/hellas/misc&#58;unscaled"
  FontPath     "/usr/share/fonts/hellas/75dpi&#58;unscaled"
  FontPath     "/usr/share/fonts/hellas/100dpi&#58;unscaled"
  FontPath     "/usr/share/fonts/hellas/Type1"
  FontPath     "/usr/share/fonts/misc/sgi&#58;unscaled"
  FontPath     "/usr/share/fonts/xtest"
  FontPath     "/opt/kde3/share/fonts"
  InputDevices "/dev/gpmdata"
  InputDevices "/dev/input/mice"
EndSection

Section "ServerFlags"
  Option       "AIGLX" "on"
  Option       "AllowMouseOpenFail" "on"
  Option       "ZapWarning" "on"
EndSection

Section "Module"
  Load         "dbe"
  Load         "freetype"
  Load         "glx"
  Load         "extmod"
  Load         "dri"
EndSection

Section "InputDevice"
  Driver       "kbd"
  Identifier   "Keyboard&#91;0&#93;"
  Option       "Protocol" "Standard"
  Option       "XkbLayout" "de"
  Option       "XkbModel" "microsoftpro"
  Option       "XkbRules" "xfree86"
  Option       "XkbVariant" "nodeadkeys"
EndSection

Section "InputDevice"
  Driver       "mouse"
  Identifier   "Mouse&#91;1&#93;"
  Option       "AutoSoft" "on"
  Option       "Device" "/dev/input/mice"
  Option       "Emulate3Buttons" "on"
  Option       "Name" "<undefined>"
  Option       "Protocol" "Auto"
  Option       "Vendor" "Sysp"
EndSection

Section "InputDevice"
  Driver       "mouse"
  Identifier   "Mouse&#91;3&#93;"
  Option       "Buttons" "5"
  Option       "Device" "/dev/input/mice"
  Option       "Name" "ImPS/2 Generic Wheel Mouse"
  Option       "Protocol" "explorerps/2"
  Option       "Vendor" "Sysp"
  Option       "ZAxisMapping" "4 5"
EndSection

Section "Monitor"
  DisplaySize  300 225
  HorizSync    30-30
  Identifier   "Monitor&#91;0&#93;"
  Option       "PreferredMode" "768x576"
  VertRefresh  50-61
  UseModes     "Modes&#91;0&#93;"
EndSection

Section "Modes"
  Identifier   "Modes&#91;0&#93;"
  Modeline 	"768x576" 94.00 1024 1072 1168 1376 768 769 772 808 +HSync +VSync
  Modeline 	"768x576" 108.00 1280 1376 1488 1800 960 961 964 1000
EndSection

Section "Screen"
  DefaultDepth 24
  SubSection "Display"
    Depth      15
    Modes      "768x576" "640x480" 
    Virtual    2048 1200
  EndSubSection
  SubSection "Display"
    Depth      16
    Modes      "768x576" "640x480" 
    Virtual    2048 1200
  EndSubSection
  SubSection "Display"
    Depth      24
    Modes      "768x576" "640x480" 
    Virtual    2048 1200
  EndSubSection
  SubSection "Display"
    Depth      8
    Modes      "768x576" "640x480" 
    Virtual    2048 1200
  EndSubSection
  Device       "Device&#91;0&#93;"
  Identifier   "Screen&#91;0&#93;"
  Monitor      "Monitor&#91;0&#93;"
EndSection

Section "Device"
  BoardName    "945G"
  Driver       "intel"
  Identifier   "Device&#91;0&#93;"
  Option       "SaXDualHead"
  Option       "SaXDualMonitorVendor" "SRC"
  Option       "SaXDualOrientation" "LeftOf"
  Option       "SaXDualResolution" "768x576"
  Option       "SaXDualMode" "Clone"
  Option       "SaXDualHSync" "30-50"
  Option       "SaXDualMonitorModel" "TV"
  Option       "SaXDualVSync" "50-61"
  Option       "SaXExternal" "Identifier&TV+DisplaySize&+VendorName&SRC+PreferredMode&768x576+HorizSync&30-50+VertRefresh&50-61"
  Screen       0
  VendorName   "Intel"
EndSection

Section "Monitor"
  HorizSync    30-50
  Identifier   "TV"
  Option       "PreferredMode" "768x576"
  VendorName   "SRC"
  VertRefresh  50-61
EndSection

Section "ServerLayout"
  Identifier   "Layout&#91;all&#93;"
  InputDevice  "Keyboard&#91;0&#93;" "CoreKeyboard"
  InputDevice  "Mouse&#91;1&#93;" "CorePointer"
  Option       "Clone" "off"
  Option       "Xinerama" "off"
  Screen       "Screen&#91;0&#93;"
EndSection

Section "DRI"
    Group      "video"
    Mode       0660
EndSection

Section "Extensions"
  Option       "Composite" "on"
EndSection

Ich habe mal nur um sicher zu gehen auch meinen normalen Monitor angepasst, jedoch ändert sich nichts am rollen des Fernseherbildes.

Stimmt die config nicht?

Danke

User avatar
Janka
Posts: 3585
Joined: 11. Feb 2006 19:10

#4 Post by Janka »

inixlinux wrote: Section "Monitor"
DisplaySize 300 225
HorizSync 30-30
Falsch, das *muss* 15-16 heißen.
Identifier "Monitor[0]"
Option "PreferredMode" "768x576"
VertRefresh 50-61
UseModes "Modes[0]"
EndSection
Das ist ok.
Section "Modes"
Identifier "Modes[0]"
Modeline "768x576" 94.00 1024 1072 1168 1376 768 769 772 808 +HSync +VSync
Modeline "768x576" 108.00 1280 1376 1488 1800 960 961 964 1000
EndSection
Das ist einmal ein Mode mit positiver Sync-Polarität. Ein Ferni braucht negative Polarität. Und dann sind diese Modelines so ganz bestimmt nicht von sax2 erzeugt worden. Die erste Modeline gehört nämlich zu einem 1024x768-Modus bei 85Hz, die zweite zu einem 1280x960-Modus bei 60Hz. Wie ich das herausgefunden habe? Durch rechnen. Nimm einen der Modi oben, vorzugsweise den hier:

Code: Select all

Modeline "pal_768x576" 14.75 768 784 864 944 576 582 588 625 -hsync -vsync interlace # H 15625 &#91;Hz&#93;, V 50 &#91;Hz&#93;
und benenne ihn in "768x576" um. Zusammen mit der Korrektur der Einstellung oben sollte das dann passen.

Ist das eine Grafikkarte mit zwei Ausgängen? Wenn ja, solltest du diesen Modus natürlich nur für den TV-Ausgang einstellen, sonst kannst du mit einem normalen PC-Monitor nichts sehen.

Janka
Ich vertonne Spam immer in /dev/dsp statt /dev/null.
Ich mag die Schreie.

inixlinux

#5 Post by inixlinux »

ich habe festgestelt, das Sax2 die xorg.conf nach einem neustart des Grafiksystems zum übernehmen der Einstellungen ändert, daher auch die falschen Werte meiner xorg.conf.

habe hier nochmal eine geänderte xorg.conf. Wo und wie kann ich hier angeben, dass der 2 Monitor (TV) eine negative sync hat bei SaxExternal? und wie gebe ich es dort an.

Code: Select all

# /.../
# SaX generated X11 config file
# Created on&#58; 2010-01-19T20&#58;17&#58;24+0100.
#
# Version&#58; 8.1
# Contact&#58; Marcus Schaefer <sax@suse.de>, 2005
# Contact&#58; SaX-User list <https&#58;//lists.berlios.de/mailman/listinfo/sax-users>
#
# Automatically generated by &#91;ISaX&#93; &#40;8.1&#41;
# PLEASE DO NOT EDIT THIS FILE!
#

Section "Files"
  FontPath     "/usr/share/fonts/misc&#58;unscaled"
  FontPath     "/usr/share/fonts/local"
  FontPath     "/usr/share/fonts/75dpi&#58;unscaled"
  FontPath     "/usr/share/fonts/100dpi&#58;unscaled"
  FontPath     "/usr/share/fonts/Type1"
  FontPath     "/usr/share/fonts/URW"
  FontPath     "/usr/share/fonts/Speedo"
  FontPath     "/usr/share/fonts/PEX"
  FontPath     "/usr/share/fonts/cyrillic"
  FontPath     "/usr/share/fonts/latin2/misc&#58;unscaled"
  FontPath     "/usr/share/fonts/latin2/75dpi&#58;unscaled"
  FontPath     "/usr/share/fonts/latin2/100dpi&#58;unscaled"
  FontPath     "/usr/share/fonts/latin2/Type1"
  FontPath     "/usr/share/fonts/latin7/75dpi&#58;unscaled"
  FontPath     "/usr/share/fonts/baekmuk&#58;unscaled"
  FontPath     "/usr/share/fonts/japanese&#58;unscaled"
  FontPath     "/usr/share/fonts/kwintv"
  FontPath     "/usr/share/fonts/truetype"
  FontPath     "/usr/share/fonts/uni&#58;unscaled"
  FontPath     "/usr/share/fonts/CID"
  FontPath     "/usr/share/fonts/ucs/misc&#58;unscaled"
  FontPath     "/usr/share/fonts/ucs/75dpi&#58;unscaled"
  FontPath     "/usr/share/fonts/ucs/100dpi&#58;unscaled"
  FontPath     "/usr/share/fonts/hellas/misc&#58;unscaled"
  FontPath     "/usr/share/fonts/hellas/75dpi&#58;unscaled"
  FontPath     "/usr/share/fonts/hellas/100dpi&#58;unscaled"
  FontPath     "/usr/share/fonts/hellas/Type1"
  FontPath     "/usr/share/fonts/misc/sgi&#58;unscaled"
  FontPath     "/usr/share/fonts/xtest"
  FontPath     "/opt/kde3/share/fonts"
  InputDevices "/dev/gpmdata"
  InputDevices "/dev/input/mice"
EndSection

Section "ServerFlags"
  Option       "AIGLX" "on"
  Option       "AllowMouseOpenFail" "on"
  Option       "ZapWarning" "on"
EndSection

Section "Module"
  Load         "glx"
  Load         "dbe"
  Load         "extmod"
  Load         "freetype"
  Load         "dri"
EndSection

Section "InputDevice"
  Driver       "kbd"
  Identifier   "Keyboard&#91;0&#93;"
  Option       "Protocol" "Standard"
  Option       "XkbLayout" "de"
  Option       "XkbModel" "microsoftpro"
  Option       "XkbRules" "xfree86"
  Option       "XkbVariant" "nodeadkeys"
EndSection


Section "InputDevice"
  Driver       "mouse"
  Identifier   "Mouse&#91;1&#93;"
  Option       "Buttons" "5"
  Option       "Device" "/dev/input/mice"
  Option       "Name" "ImPS/2 Generic Wheel Mouse"
  Option       "Protocol" "explorerps/2"
  Option       "Vendor" "Sysp"
  Option       "ZAxisMapping" "4 5"
EndSection


Section "Monitor"
  Option       "CalcAlgorithm" "XServerPool"
  DisplaySize  300 225
  HorizSync    30-70
  Identifier   "Monitor&#91;0&#93;"
  ModelName    "VESA DDC1/2B MONITOR"
  Option       "DPMS"
  Option       "PreferredMode" "1280x1024"
  VendorName   "SRC"
  VertRefresh  43-120
  UseModes     "Modes&#91;0&#93;"
EndSection


Section "Modes"
  Identifier   "Modes&#91;0&#93;"
  Modeline 	"1024x768" 94 1024 1072 1168 1376 768 769 772 808 +hsync +vsync
EndSection


Section "Screen"
  DefaultDepth 24
  SubSection "Display"
    Depth      15
    Modes      "1280x1024" "1280x960" "1280x800" "1152x864" "1280x768" "1280x720" "1024x768" "1280x600" "1024x600" "800x600" "768x576" "640x480" 
    Virtual    2048 1200
  EndSubSection
  SubSection "Display"
    Depth      16
    Modes      "1280x1024" "1280x960" "1280x800" "1152x864" "1280x768" "1280x720" "1024x768" "1280x600" "1024x600" "800x600" "768x576" "640x480" 
    Virtual    2048 1200
  EndSubSection
  SubSection "Display"
    Depth      24
    Modes      "1280x1024" "1280x960" "1280x800" "1152x864" "1280x768" "1280x720" "1024x768" "1280x600" "1024x600" "800x600" "768x576" "640x480" 
    Virtual    2048 1200
  EndSubSection
  SubSection "Display"
    Depth      8
    Modes      "1280x1024" "1280x960" "1280x800" "1152x864" "1280x768" "1280x720" "1024x768" "1280x600" "1024x600" "800x600" "768x576" "640x480" 
    Virtual    2048 1200
  EndSubSection
  Device       "Device&#91;0&#93;"
  Identifier   "Screen&#91;0&#93;"
  Monitor      "Monitor&#91;0&#93;"
EndSection


Section "Device"
  BoardName    "945G"
  Driver       "intel"
  Identifier   "Device&#91;0&#93;"
  Option       "SaXDualHead"
  Option       "monitor-VGA" "Monitor&#91;0&#93;"
  Option       "SaXDualMonitorVendor" "--> LCD"
  Option       "SaXDualOrientation" "LeftOf"
  Option       "SaXDualResolution" "768x576"
  Option       "monitor-TV-1" "EXT"
  Option       "SaXDualMode" "Clone"
  Option       "SaXDualHSync" "15-16"
  Option       "SaXDualMonitorModel" "800X600@60HZ"
  Option       "SaXDualVSync" "50-61"
  Option       "SaXExternal" "Identifier&EXT+DisplaySize&+VendorName&--> LCD+PreferredMode&768x576+HorizSync&15-16+ModelName&800X600@60HZ+VertRefresh&50-61"
  Screen       0
  VendorName   "Intel"
EndSection


Section "Monitor"
  HorizSync    15-16
  Identifier   "EXT"
  ModelName    "800X600@60HZ"
  Option       "PreferredMode" "768x576"
  VendorName   "--> LCD"
  VertRefresh  50-61
EndSection


Section "ServerLayout"
  Identifier   "Layout&#91;all&#93;"
  InputDevice  "Keyboard&#91;0&#93;" "CoreKeyboard"
  InputDevice  "Mouse&#91;1&#93;" "CorePointer"
  Option       "Clone" "off"
  Option       "Xinerama" "off"
  Screen       "Screen&#91;0&#93;"
EndSection


Section "DRI"
    Group      "video"
    Mode       0660
EndSection

Section "Extensions"
  Option	"Composite" "Enable"
EndSection

danke

User avatar
Janka
Posts: 3585
Joined: 11. Feb 2006 19:10

#6 Post by Janka »

Du musst Sax und die davon erzeugte Konfiguration ignorieren. Du kannst entweder ein automatisches Werkzeug benutzen oder es von Hand machen. Beides gemischt führt zu Kuddelmuddel.

Janka
Ich vertonne Spam immer in /dev/dsp statt /dev/null.
Ich mag die Schreie.

inixlinux

#7 Post by inixlinux »

So jetzt hab ich mal die xorg.conf von Hand konfiguriert.

Start ich aber nun den X-Server meckert er, dass er keine modes hat
(Output TV-1 enabled but has no modes found)
# /.../
# SaX generated X11 config file
# Created on: 2010-01-21T20:04:35+0100.
#
# Version: 8.1
# Contact: Marcus Schaefer <sax@suse.de>, 2005
# Contact: SaX-User list <https://lists.berlios.de/mailman/listinfo/sax-users>
#
# Automatically generated by [ISaX] (8.1)
# PLEASE DO NOT EDIT THIS FILE!
#

Section "Files"
FontPath "/usr/share/fonts/misc:unscaled"
FontPath "/usr/share/fonts/local"
FontPath "/usr/share/fonts/75dpi:unscaled"
FontPath "/usr/share/fonts/100dpi:unscaled"
FontPath "/usr/share/fonts/Type1"
FontPath "/usr/share/fonts/URW"
FontPath "/usr/share/fonts/Speedo"
FontPath "/usr/share/fonts/PEX"
FontPath "/usr/share/fonts/cyrillic"
FontPath "/usr/share/fonts/latin2/misc:unscaled"
FontPath "/usr/share/fonts/latin2/75dpi:unscaled"
FontPath "/usr/share/fonts/latin2/100dpi:unscaled"
FontPath "/usr/share/fonts/latin2/Type1"
FontPath "/usr/share/fonts/latin7/75dpi:unscaled"
FontPath "/usr/share/fonts/baekmuk:unscaled"
FontPath "/usr/share/fonts/japanese:unscaled"
FontPath "/usr/share/fonts/kwintv"
FontPath "/usr/share/fonts/truetype"
FontPath "/usr/share/fonts/uni:unscaled"
FontPath "/usr/share/fonts/CID"
FontPath "/usr/share/fonts/ucs/misc:unscaled"
FontPath "/usr/share/fonts/ucs/75dpi:unscaled"
FontPath "/usr/share/fonts/ucs/100dpi:unscaled"
FontPath "/usr/share/fonts/hellas/misc:unscaled"
FontPath "/usr/share/fonts/hellas/75dpi:unscaled"
FontPath "/usr/share/fonts/hellas/100dpi:unscaled"
FontPath "/usr/share/fonts/hellas/Type1"
FontPath "/usr/share/fonts/misc/sgi:unscaled"
FontPath "/usr/share/fonts/xtest"
FontPath "/opt/kde3/share/fonts"
InputDevices "/dev/gpmdata"
InputDevices "/dev/input/mice"
EndSection

Section "ServerFlags"
Option "AIGLX" "on"
Option "AllowMouseOpenFail" "on"
Option "ZapWarning" "on"
EndSection

Section "Module"
Load "glx"
Load "dbe"
Load "extmod"
Load "freetype"
Load "dri"
EndSection

Section "InputDevice"
Driver "kbd"
Identifier "Keyboard[0]"
Option "Protocol" "Standard"
Option "XkbLayout" "de"
Option "XkbModel" "microsoftpro"
Option "XkbRules" "xfree86"
Option "XkbVariant" "nodeadkeys"
EndSection


Section "InputDevice"
Driver "mouse"
Identifier "Mouse[1]"
Option "Buttons" "5"
Option "Device" "/dev/input/mice"
Option "Name" "ImPS/2 Generic Wheel Mouse"
Option "Protocol" "explorerps/2"
Option "Vendor" "Sysp"
Option "ZAxisMapping" "4 5"
EndSection


Section "Monitor"
Option "CalcAlgorithm" "XServerPool"
DisplaySize 300 225
HorizSync 30-70
Identifier "EXT1"
ModelName "VESA DDC1/2B MONITOR"
Option "DPMS"
Option "PreferredMode" "1280x1024"
Option "Ignore" "false"
VendorName "SRC"
VertRefresh 43-120
UseModes "Modes[0]"
EndSection


Section "Modes"
Identifier "Modes[0]"
Modeline "1024x768" 94 1024 1072 1168 1376 768 769 772 808 +hsync +vsync
EndSection



Section "Screen"
DefaultDepth 24
SubSection "Display"
Depth 15
Modes "1280x1024" "1280x960" "1280x800" "1152x864" "1280x768" "1280x720" "1024x768" "1280x600" "1024x600" "800x600" "768x576" "640x480"
Virtual 2048 1200
EndSubSection
SubSection "Display"
Depth 16
Modes "1280x1024" "1280x960" "1280x800" "1152x864" "1280x768" "1280x720" "1024x768" "1280x600" "1024x600" "800x600" "768x576" "640x480"
Virtual 2048 1200
EndSubSection
SubSection "Display"
Depth 24
Modes "1280x1024" "1280x960" "1280x800" "1152x864" "1280x768" "1280x720" "1024x768" "1280x600" "1024x600" "800x600" "768x576" "640x480"
Virtual 2048 1200
EndSubSection
SubSection "Display"
Depth 8
Modes "1280x1024" "1280x960" "1280x800" "1152x864" "1280x768" "1280x720" "1024x768" "1280x600" "1024x600" "800x600" "768x576" "640x480"
Virtual 2048 1200
EndSubSection
Device "Device[0]"
Identifier "Screen[0]"
Monitor "EXT1"
EndSection


Section "Device"
BoardName "945G"
Driver "intel"
Identifier "Device[0]"
Option "SaXDualHead"
Option "monitor-VGA" "EXT1"
Option "SaXDualMonitorVendor" "SRC"
Option "SaXDualOrientation" "LeftOf"
Option "SaXDualResolution" "1280x1024"
Option "monitor-TV-1" "TV"
Option "SaXDualMode" "Clone"
Option "SaXDualHSync" "30-70"
Option "SaXDualMonitorModel" "VESA DDC1/2B MONITOR"
Option "SaXDualVSync" "50-120"
Option "SaXExternal" "Identifier&TV+DisplaySize&+VendorName&SRC+PreferredMode&768x576+HorizSync&15-16+ModelName&VESA DDC1/2B MONITOR+VertRefresh&50-61"
Screen 0
VendorName "Intel"
EndSection


Section "Monitor"
HorizSync 15-16
Identifier "TV"
VertRefresh 49.0-61.0
UseModes "Modes[TV]"
EndSection

Section "Modes"
Identifier "Modes[TV]"
Modeline "ntsc_320x240" 6.04186 320 328 352 384 240 244 247 262 -hsync -vsync # H 15734 [Hz], V 60.0534 [Hz]
Modeline "ntsc_400x300" 7.55232 400 408 448 480 300 398 404 525 -hsync -vsync interlace # H 15734 [Hz], V 59.939 [Hz]
Modeline "ntsc_512x384" 9.69214 512 528 568 616 384 440 446 525 -hsync -vsync interlace # H 15734 [Hz], V 59.939 [Hz]
Modeline "ntsc_640x480" 12.2096 640 664 720 776 480 488 494 525 -hsync -vsync interlace # H 15734 [Hz], V 59.939 [Hz]
Modeline "ntsc_720x480" 13.72 720 744 808 872 480 488 494 525 -hsync -vsync interlace # H 15734 [Hz], V 59.939 [Hz]
Modeline "ntsc_720x480jk" 13.72 720 744 778 872 480 488 494 525 +hsync +vsync interlace # H 15734 [Hz], V 59.939 [Hz]

Modeline "ntsc_320x242" 6.04186 320 328 352 384 242 245 248 262 -hsync -vsync # H 15734 [Hz], V 60.0534 [Hz]
Modeline "ntsc_640x484" 12.0837 640 656 704 768 484 490 496 525 -hsync -vsync interlace # H 15734 [Hz], V 59.939 [Hz]

Modeline "320x240" 6.125 320 328 360 392 240 267 270 312 -hsync -vsync # H 15625 [Hz], V 50.0801 [Hz]
Modeline "400x300" 7.75 400 416 456 496 300 444 450 625 -hsync -vsync interlace # H 15625 [Hz], V 50 [Hz]
Modeline "512x384" 9.875 512 528 576 632 384 486 492 625 -hsync -vsync interlace # H 15625 [Hz], V 50 [Hz]
Modeline "640x480" 12.25 640 656 712 784 480 534 540 625 -hsync -vsync interlace # H 15625 [Hz], V 50 [Hz]

Modeline "768x576" 14.75 768 784 864 944 576 582 588 625 -hsync -vsync interlace # H 15625 [Hz], V 50 [Hz]
Modeline "720x576" 13.875 720 744 808 888 576 582 588 625 -hsync -vsync interlace # H 15625 [Hz], V 50 [Hz]
EndSection

Section "ServerLayout"
Identifier "Layout[all]"
InputDevice "Keyboard[0]" "CoreKeyboard"
InputDevice "Mouse[1]" "CorePointer"
Option "Clone" "off"
Option "Xinerama" "off"
Screen "Screen[0]"
EndSection


Section "DRI"
Group "video"
Mode 0660
EndSection

Section "Extensions"
EndSection
danke

User avatar
Janka
Posts: 3585
Joined: 11. Feb 2006 19:10

#8 Post by Janka »

Die "SaX..."-Options kannst du rauswerfen, die bewirken im Treiber nichts und verwirren dich nur.

Du brauchst für den zweiten Monitor (den Ferni) eine eigene Screen-Sektion z.B. "Screen[TV]", wo dann die zu benutzenden Modi gelistet sind. Ich schlage vor, erst einmal nur den Modus "768x576" dort einzutragen.

Dann muss du noch in der Sektion "ServerLayout" eine Zeile
Screen "Screen[TV]" rightof "Screen[0]" eintragen.

Janka
Ich vertonne Spam immer in /dev/dsp statt /dev/null.
Ich mag die Schreie.

inixlinux

#9 Post by inixlinux »

da er mir sagt, dass er keinen modus für den TV Anschluss findet habe ich jetzt mal alle eingebaut:

Code: Select all

Section "Screen"
DefaultDepth 24
SubSection "Display"
Depth 15
Modes "1280x1024" "1280x960" "1280x800" "1152x864" "1280x768" "1280x720" "1024x768" "1280x600" "1024x600" "800x600" "768x576" "640x480"
Virtual 2048 1200
EndSubSection
SubSection "Display"
Depth 16
Modes "1280x1024" "1280x960" "1280x800" "1152x864" "1280x768" "1280x720" "1024x768" "1280x600" "1024x600" "800x600" "768x576" "640x480"
Virtual 2048 1200
EndSubSection
SubSection "Display"
Depth 24
Modes "1280x1024" "1280x960" "1280x800" "1152x864" "1280x768" "1280x720" "1024x768" "1280x600" "1024x600" "800x600" "768x576" "640x480"
Virtual 2048 1200
EndSubSection
SubSection "Display"
Depth 8
Modes "1280x1024" "1280x960" "1280x800" "1152x864" "1280x768" "1280x720" "1024x768" "1280x600" "1024x600" "800x600" "768x576" "640x480"
Virtual 2048 1200
EndSubSection
Device "Device&#91;0&#93;"
Identifier "Screen&#91;TV&#93;"
Monitor "TV"
EndSection
füre ich xrandr -q aus bekomme ich als Meldung auch:

xrandr: Output TV-1 is not disconnected but has no modes


kann es sein, dass dies ein Treiberproblem ist ich verzweifle hier echt noch.

danke

User avatar
Janka
Posts: 3585
Joined: 11. Feb 2006 19:10

#10 Post by Janka »

Bitte bau für den zweiten Ausgang *nur* den 768x576-Modus rein, sonst sieht man bei der Fehlersuche den Wald vor lauter Bäumen nicht.

Danach starte den X-Server neu (zweimal kurz nacheinander Strg+Alt+Backspace) und poste bitte die /var/log/Xorg.0.log, da steht drin, warum und wieso es nicht klappt.

Janka
Ich vertonne Spam immer in /dev/dsp statt /dev/null.
Ich mag die Schreie.

inixlinux

#11 Post by inixlinux »

So hab die Screen Sction für den 2 Monitor angepasst und nur noch den Modus 768x576 drin.

in der Xorg.0.log steht das er für den TV-Ausgang keinen Modus gefunden hat.

hier die /var/log/Xorg.0.log

Code: Select all

_XSERVTransSocketOpenCOTSServer&#58; Unable to open socket for inet6
_XSERVTransOpen&#58; transport open failed for inet6/Server-LB&#58;0
_XSERVTransMakeAllCOTSServerListeners&#58; failed to open listener for inet6

X.Org X Server 1.5.2
Release Date&#58; 10 October 2008
X Protocol Version 11, Revision 0
Build Operating System&#58; openSUSE SUSE LINUX
Current Operating System&#58; Linux Server-LB 2.6.27.42-0.1-pae #1 SMP 2010-01-06 16&#58;07&#58;25 +0100 i686
Build Date&#58; 02 July 2009  08&#58;02&#58;13AM
 
	Before reporting problems, check http&#58;//wiki.x.org
	to make sure that you have the latest version.
Module Loader present
Markers&#58; &#40;--&#41; probed, &#40;**&#41; from config file, &#40;==&#41; default setting,
	&#40;++&#41; from command line, &#40;!!&#41; notice, &#40;II&#41; informational,
	&#40;WW&#41; warning, &#40;EE&#41; error, &#40;NI&#41; not implemented, &#40;??&#41; unknown.
&#40;==&#41; Log file&#58; "/var/log/Xorg.0.log", Time&#58; Sat Jan 23 15&#58;17&#58;06 2010
&#40;==&#41; Using config file&#58; "/etc/X11/xorg.conf"
&#40;==&#41; ServerLayout "Layout&#91;all&#93;"
&#40;**&#41; |-->Screen "Screen&#91;TV&#93;" &#40;0&#41;
&#40;**&#41; |   |-->Monitor "TV"
&#40;**&#41; |   |-->Device "Device&#91;0&#93;"
&#40;EE&#41; Screen Screen&#91;0&#93; doesn't exist&#58; deleting placement
&#40;**&#41; |-->Input Device "Keyboard&#91;0&#93;"
&#40;**&#41; |-->Input Device "Mouse&#91;1&#93;"
&#40;**&#41; Option "ZapWarning" "on"
&#40;**&#41; Option "AllowMouseOpenFail" "on"
&#40;**&#41; Option "Xinerama" "off"
&#40;**&#41; Option "AIGLX" "on"
&#40;==&#41; Automatically adding devices
&#40;==&#41; Automatically enabling devices
&#40;WW&#41; The directory "/usr/share/fonts/local" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/PEX" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/latin2/misc" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/latin2/75dpi" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/latin2/100dpi" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/latin2/Type1" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/latin7/75dpi" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/baekmuk" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/japanese" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/kwintv" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/uni" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/CID" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/ucs/misc" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/ucs/75dpi" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/ucs/100dpi" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/hellas/misc" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/hellas/75dpi" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/hellas/100dpi" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/hellas/Type1" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/misc/sgi" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/xtest" does not exist.
	Entry deleted from font path.
&#40;==&#41; Including the default font path /usr/share/fonts/misc&#58;unscaled,/usr/share/fonts/TTF/,/usr/share/fonts/OTF,/usr/share/fonts/Type1/,/usr/share/fonts/100dpi&#58;unscaled,/usr/share/fonts/75dpi&#58;unscaled.
&#40;**&#41; FontPath set to&#58;
	/usr/share/fonts/misc&#58;unscaled,
	/usr/share/fonts/75dpi&#58;unscaled,
	/usr/share/fonts/100dpi&#58;unscaled,
	/usr/share/fonts/Type1,
	/usr/share/fonts/URW,
	/usr/share/fonts/Speedo,
	/usr/share/fonts/cyrillic,
	/usr/share/fonts/truetype,
	/opt/kde3/share/fonts,
	/usr/share/fonts/misc&#58;unscaled,
	/usr/share/fonts/TTF/,
	/usr/share/fonts/OTF,
	/usr/share/fonts/Type1/,
	/usr/share/fonts/100dpi&#58;unscaled,
	/usr/share/fonts/75dpi&#58;unscaled
&#40;**&#41; Input device list set to "/dev/gpmdata,/dev/input/mice"
&#40;==&#41; ModulePath set to "/usr/lib/xorg/modules/updates,/usr/lib/xorg/modules"
&#40;II&#41; Open ACPI successful &#40;/var/run/acpid.socket&#41;
&#40;II&#41; Loader magic&#58; 0x81f95c0
&#40;II&#41; Module ABI versions&#58;
	X.Org ANSI C Emulation&#58; 0.4
	X.Org Video Driver&#58; 4.1
	X.Org XInput driver &#58; 2.1
	X.Org Server Extension &#58; 1.1
	X.Org Font Renderer &#58; 0.6
&#40;II&#41; Loader running on linux
&#40;++&#41; using VT number 7

&#40;--&#41; PCI&#58;*&#40;0@0&#58;2&#58;0&#41; unknown vendor &#40;0x8086&#41; unknown chipset &#40;0x2772&#41; rev 2, Mem @ 0x50200000/0, 0x40000000/0, 0x50280000/0, I/O @ 0x000020e0/0
&#40;II&#41; System resource ranges&#58;
	&#91;0&#93; -1	0	0xffffffff - 0xffffffff &#40;0x1&#41; MX&#91;B&#93;
	&#91;1&#93; -1	0	0x000f0000 - 0x000fffff &#40;0x10000&#41; MX&#91;B&#93;
	&#91;2&#93; -1	0	0x000c0000 - 0x000effff &#40;0x30000&#41; MX&#91;B&#93;
	&#91;3&#93; -1	0	0x00000000 - 0x0009ffff &#40;0xa0000&#41; MX&#91;B&#93;
	&#91;4&#93; -1	0	0x0000ffff - 0x0000ffff &#40;0x1&#41; IX&#91;B&#93;
	&#91;5&#93; -1	0	0x00000000 - 0x00000000 &#40;0x1&#41; IX&#91;B&#93;
&#40;II&#41; "extmod" will be loaded. This was enabled by default and also specified in the config file.
&#40;II&#41; "dbe" will be loaded. This was enabled by default and also specified in the config file.
&#40;II&#41; "glx" will be loaded. This was enabled by default and also specified in the config file.
&#40;II&#41; "freetype" will be loaded. This was enabled by default and also specified in the config file.
&#40;II&#41; "record" will be loaded by default.
&#40;II&#41; "dri" will be loaded. This was enabled by default and also specified in the config file.
&#40;II&#41; LoadModule&#58; "glx"

&#40;II&#41; Loading /usr/lib/xorg/modules//extensions/libglx.so
&#40;II&#41; Module glx&#58; vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 1.0.0
	ABI class&#58; X.Org Server Extension, version 1.1
&#40;**&#41; AIGLX enabled
&#40;**&#41; Exporting typical set of GLX visuals
&#40;II&#41; Loading extension GLX
&#40;II&#41; LoadModule&#58; "dbe"

&#40;II&#41; Loading /usr/lib/xorg/modules//extensions/libdbe.so
&#40;II&#41; Module dbe&#58; vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 1.0.0
	Module class&#58; X.Org Server Extension
	ABI class&#58; X.Org Server Extension, version 1.1
&#40;II&#41; Loading extension DOUBLE-BUFFER
&#40;II&#41; LoadModule&#58; "extmod"

&#40;II&#41; Loading /usr/lib/xorg/modules//extensions/libextmod.so
&#40;II&#41; Module extmod&#58; vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 1.0.0
	Module class&#58; X.Org Server Extension
	ABI class&#58; X.Org Server Extension, version 1.1
&#40;II&#41; Loading extension SHAPE
&#40;II&#41; Loading extension MIT-SUNDRY-NONSTANDARD
&#40;II&#41; Loading extension BIG-REQUESTS
&#40;II&#41; Loading extension SYNC
&#40;II&#41; Loading extension MIT-SCREEN-SAVER
&#40;II&#41; Loading extension XC-MISC
&#40;II&#41; Loading extension XFree86-VidModeExtension
&#40;II&#41; Loading extension XFree86-Misc
&#40;II&#41; Loading extension XFree86-DGA
&#40;II&#41; Loading extension DPMS
&#40;II&#41; Loading extension TOG-CUP
&#40;II&#41; Loading extension Extended-Visual-Information
&#40;II&#41; Loading extension XVideo
&#40;II&#41; Loading extension XVideo-MotionCompensation
&#40;II&#41; Loading extension X-Resource
&#40;II&#41; LoadModule&#58; "freetype"

&#40;II&#41; Loading /usr/lib/xorg/modules//fonts/libfreetype.so
&#40;II&#41; Module freetype&#58; vendor="X.Org Foundation & the After X-TT Project"
	compiled for 1.5.2, module version = 2.1.0
	Module class&#58; X.Org Font Renderer
	ABI class&#58; X.Org Font Renderer, version 0.6
&#40;II&#41; Loading font FreeType
&#40;II&#41; LoadModule&#58; "dri"

&#40;II&#41; Loading /usr/lib/xorg/modules//extensions/libdri.so
&#40;II&#41; Module dri&#58; vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 1.0.0
	ABI class&#58; X.Org Server Extension, version 1.1
&#40;II&#41; Loading extension XFree86-DRI
&#40;II&#41; LoadModule&#58; "record"

&#40;II&#41; Loading /usr/lib/xorg/modules//extensions/librecord.so
&#40;II&#41; Module record&#58; vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 1.13.0
	Module class&#58; X.Org Server Extension
	ABI class&#58; X.Org Server Extension, version 1.1
&#40;II&#41; Loading extension RECORD
&#40;II&#41; LoadModule&#58; "intel"

&#40;II&#41; Loading /usr/lib/xorg/modules//drivers/intel_drv.so
&#40;II&#41; Module intel&#58; vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 2.5.0
	Module class&#58; X.Org Video Driver
	ABI class&#58; X.Org Video Driver, version 4.1
&#40;II&#41; LoadModule&#58; "kbd"

&#40;II&#41; Loading /usr/lib/xorg/modules//input/kbd_drv.so
&#40;II&#41; Module kbd&#58; vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 1.3.1
	Module class&#58; X.Org XInput Driver
	ABI class&#58; X.Org XInput driver, version 2.1
&#40;II&#41; LoadModule&#58; "mouse"

&#40;II&#41; Loading /usr/lib/xorg/modules//input/mouse_drv.so
&#40;II&#41; Module mouse&#58; vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 1.3.0
	Module class&#58; X.Org XInput Driver
	ABI class&#58; X.Org XInput driver, version 2.1
&#40;II&#41; intel&#58; Driver for Intel Integrated Graphics Chipsets&#58; i810,
	i810-dc100, i810e, i815, i830M, 845G, 852GM/855GM, 865G, 915G,
	E7221 &#40;i915&#41;, 915GM, 945G, 945GM, 945GME, 965G, G35, 965Q, 946GZ,
	965GM, 965GME/GLE, G33, Q35, Q33,
	Mobile Intel® GM45 Express Chipset,
	Intel Integrated Graphics Device, G45/G43, Q45/Q43, G41
&#40;II&#41; Primary Device is&#58; PCI 00@00&#58;02&#58;0
&#40;II&#41; resource ranges after xf86ClaimFixedResources&#40;&#41; call&#58;
	&#91;0&#93; -1	0	0xffffffff - 0xffffffff &#40;0x1&#41; MX&#91;B&#93;
	&#91;1&#93; -1	0	0x000f0000 - 0x000fffff &#40;0x10000&#41; MX&#91;B&#93;
	&#91;2&#93; -1	0	0x000c0000 - 0x000effff &#40;0x30000&#41; MX&#91;B&#93;
	&#91;3&#93; -1	0	0x00000000 - 0x0009ffff &#40;0xa0000&#41; MX&#91;B&#93;
	&#91;4&#93; -1	0	0x0000ffff - 0x0000ffff &#40;0x1&#41; IX&#91;B&#93;
	&#91;5&#93; -1	0	0x00000000 - 0x00000000 &#40;0x1&#41; IX&#91;B&#93;
&#40;II&#41; resource ranges after probing&#58;
	&#91;0&#93; -1	0	0xffffffff - 0xffffffff &#40;0x1&#41; MX&#91;B&#93;
	&#91;1&#93; -1	0	0x000f0000 - 0x000fffff &#40;0x10000&#41; MX&#91;B&#93;
	&#91;2&#93; -1	0	0x000c0000 - 0x000effff &#40;0x30000&#41; MX&#91;B&#93;
	&#91;3&#93; -1	0	0x00000000 - 0x0009ffff &#40;0xa0000&#41; MX&#91;B&#93;
	&#91;4&#93; 0	0	0x000a0000 - 0x000affff &#40;0x10000&#41; MS&#91;B&#93;
	&#91;5&#93; 0	0	0x000b0000 - 0x000b7fff &#40;0x8000&#41; MS&#91;B&#93;
	&#91;6&#93; 0	0	0x000b8000 - 0x000bffff &#40;0x8000&#41; MS&#91;B&#93;
	&#91;7&#93; -1	0	0x0000ffff - 0x0000ffff &#40;0x1&#41; IX&#91;B&#93;
	&#91;8&#93; -1	0	0x00000000 - 0x00000000 &#40;0x1&#41; IX&#91;B&#93;
	&#91;9&#93; 0	0	0x000003b0 - 0x000003bb &#40;0xc&#41; IS&#91;B&#93;
	&#91;10&#93; 0	0	0x000003c0 - 0x000003df &#40;0x20&#41; IS&#91;B&#93;
&#40;II&#41; Loading sub module "vgahw"
&#40;II&#41; LoadModule&#58; "vgahw"

&#40;II&#41; Loading /usr/lib/xorg/modules//libvgahw.so
&#40;II&#41; Module vgahw&#58; vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 0.1.0
	ABI class&#58; X.Org Video Driver, version 4.1
&#40;**&#41; intel&#40;0&#41;&#58; Depth 24, &#40;--&#41; framebuffer bpp 32
&#40;==&#41; intel&#40;0&#41;&#58; RGB weight 888
&#40;==&#41; intel&#40;0&#41;&#58; Default visual is TrueColor
&#40;II&#41; intel&#40;0&#41;&#58; Integrated Graphics Chipset&#58; Intel&#40;R&#41; 945G
&#40;--&#41; intel&#40;0&#41;&#58; Chipset&#58; "945G"
&#40;--&#41; intel&#40;0&#41;&#58; Linear framebuffer at 0x40000000
&#40;--&#41; intel&#40;0&#41;&#58; IO registers at addr 0x50200000
&#40;WW&#41; intel&#40;0&#41;&#58; libpciaccess reported 0 rom size, guessing 64kB
&#40;==&#41; intel&#40;0&#41;&#58; Using EXA for acceleration
&#40;II&#41; intel&#40;0&#41;&#58; 2 display pipes available.
&#40;II&#41; Loading sub module "ddc"
&#40;II&#41; LoadModule&#58; "ddc"
&#40;II&#41; Module "ddc" already built-in
&#40;II&#41; Loading sub module "i2c"
&#40;II&#41; LoadModule&#58; "i2c"
&#40;II&#41; Module "i2c" already built-in
&#40;II&#41; intel&#40;0&#41;&#58; Output VGA using monitor section EXT1
&#40;**&#41; intel&#40;0&#41;&#58; Option "PreferredMode" "1280x1024"
&#40;**&#41; intel&#40;0&#41;&#58; Option "Ignore" "false"
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "SDVOCTRL_E for SDVOB" initialized.
&#40;II&#41; intel&#40;0&#41;&#58; I2C device "SDVOCTRL_E for SDVOB&#58;SDVO Controller B" registered at address 0x70.
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "SDVOB DDC Bus" initialized.
&#40;II&#41; intel&#40;0&#41;&#58; Output TV-1 using monitor section TV
&#40;II&#41; intel&#40;0&#41;&#58; SDVOB&#58; device VID/DID&#58; 02&#58;C2.02, clock range 25.0MHz - 160.0MHz
&#40;II&#41; intel&#40;0&#41;&#58; SDVOB&#58; 1 input channel
&#40;II&#41; intel&#40;0&#41;&#58; SDVOB&#58; RGB0 output reported
&#40;II&#41; intel&#40;0&#41;&#58; SDVOB&#58; CVBS0 output reported
&#40;II&#41; intel&#40;0&#41;&#58; SDVOB&#58; SVID0 output reported
&#40;II&#41; intel&#40;0&#41;&#58; SDVOB&#58; YPRPB0 output reported
&#40;II&#41; intel&#40;0&#41;&#58; SDVOB&#58; SCART0 output reported
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "SDVOCTRL_E for SDVOC" initialized.
&#40;II&#41; intel&#40;0&#41;&#58; I2C device "SDVOCTRL_E for SDVOC&#58;SDVO Controller C" registered at address 0x72.
&#40;II&#41; intel&#40;0&#41;&#58; No SDVO device found on SDVOC
&#40;II&#41; intel&#40;0&#41;&#58; I2C device "SDVOCTRL_E for SDVOC&#58;SDVO Controller C" removed.
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "SDVOCTRL_E for SDVOC" removed.
&#40;II&#41; intel&#40;0&#41;&#58; Output VGA using monitor section EXT1
&#40;II&#41; intel&#40;0&#41;&#58; Current clock rate multiplier&#58; 1
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "CRTDDC_A" initialized.
&#40;II&#41; intel&#40;0&#41;&#58; I2C device "CRTDDC_A&#58;ddc2" registered at address 0xA0.
&#40;II&#41; intel&#40;0&#41;&#58; I2C device "CRTDDC_A&#58;ddc2" removed.
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "CRTDDC_A" removed.
&#40;II&#41; intel&#40;0&#41;&#58; EDID vendor "SRC", prod id 706
&#40;II&#41; intel&#40;0&#41;&#58; Using hsync ranges from config file
&#40;II&#41; intel&#40;0&#41;&#58; Using vrefresh ranges from config file
&#40;II&#41; intel&#40;0&#41;&#58; Printing DDC gathered Modelines&#58;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x400"x0.0   31.50  640 664 704 832  400 409 412 450 -hsync +vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   94.50  1024 1072 1168 1376  768 769 772 808 +hsync +vsync &#40;68.7 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync &#40;37.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 491 520 -hsync -vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   25.20  640 656 752 800  480 490 492 525 -hsync -vsync &#40;31.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync &#40;31.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   78.80  1024 1040 1136 1312  768 769 772 800 +hsync +vsync &#40;60.1 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync &#40;56.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync &#40;48.4 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync &#40;46.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync &#40;48.1 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1280x1024"x60.0  108.88  1280 1360 1496 1712  1024 1025 1028 1060 -hsync +vsync &#40;63.6 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; EDID vendor "SRC", prod id 706
&#40;II&#41; intel&#40;0&#41;&#58; Output TV-1 using monitor section TV
&#40;II&#41; intel&#40;0&#41;&#58; Output VGA connected
&#40;II&#41; intel&#40;0&#41;&#58; Output TV-1 connected
&#40;II&#41; intel&#40;0&#41;&#58; Using user preference for initial modes
&#40;II&#41; intel&#40;0&#41;&#58; Output VGA using initial mode 1280x1024
&#40;EE&#41; intel&#40;0&#41;&#58; Output TV-1 enabled but has no modes
&#40;II&#41; intel&#40;0&#41;&#58; detected 256 kB GTT.
&#40;II&#41; intel&#40;0&#41;&#58; detected 7932 kB stolen memory.
&#40;==&#41; intel&#40;0&#41;&#58; video overlay key set to 0x101fe
&#40;==&#41; intel&#40;0&#41;&#58; Intel XvMC decoder disabled
&#40;==&#41; intel&#40;0&#41;&#58; Will not try to enable page flipping
&#40;==&#41; intel&#40;0&#41;&#58; Triple buffering disabled
&#40;==&#41; intel&#40;0&#41;&#58; Using gamma correction &#40;1.0, 1.0, 1.0&#41;
&#40;**&#41; intel&#40;0&#41;&#58; Display dimensions&#58; &#40;320, 240&#41; mm
&#40;**&#41; intel&#40;0&#41;&#58; DPI set to &#40;101, 108&#41;
&#40;II&#41; Loading sub module "fb"
&#40;II&#41; LoadModule&#58; "fb"

&#40;II&#41; Loading /usr/lib/xorg/modules//libfb.so
&#40;II&#41; Module fb&#58; vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 1.0.0
	ABI class&#58; X.Org ANSI C Emulation, version 0.4
&#40;II&#41; Loading sub module "exa"
&#40;II&#41; LoadModule&#58; "exa"

&#40;II&#41; Loading /usr/lib/xorg/modules//libexa.so
&#40;II&#41; Module exa&#58; vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 2.4.0
	ABI class&#58; X.Org Video Driver, version 4.1
&#40;II&#41; Loading sub module "ramdac"
&#40;II&#41; LoadModule&#58; "ramdac"
&#40;II&#41; Module "ramdac" already built-in
&#40;II&#41; intel&#40;0&#41;&#58; Comparing regs from server start up to After PreInit
&#40;==&#41; Depth 24 pixmap format is 32 bpp
&#40;II&#41; do I need RAC?  No, I don't.
&#40;II&#41; resource ranges after preInit&#58;
	&#91;0&#93; -1	0	0xffffffff - 0xffffffff &#40;0x1&#41; MX&#91;B&#93;
	&#91;1&#93; -1	0	0x000f0000 - 0x000fffff &#40;0x10000&#41; MX&#91;B&#93;
	&#91;2&#93; -1	0	0x000c0000 - 0x000effff &#40;0x30000&#41; MX&#91;B&#93;
	&#91;3&#93; -1	0	0x00000000 - 0x0009ffff &#40;0xa0000&#41; MX&#91;B&#93;
	&#91;4&#93; 0	0	0x000a0000 - 0x000affff &#40;0x10000&#41; MS&#91;B&#93;&#40;OprD&#41;
	&#91;5&#93; 0	0	0x000b0000 - 0x000b7fff &#40;0x8000&#41; MS&#91;B&#93;&#40;OprD&#41;
	&#91;6&#93; 0	0	0x000b8000 - 0x000bffff &#40;0x8000&#41; MS&#91;B&#93;&#40;OprD&#41;
	&#91;7&#93; -1	0	0x0000ffff - 0x0000ffff &#40;0x1&#41; IX&#91;B&#93;
	&#91;8&#93; -1	0	0x00000000 - 0x00000000 &#40;0x1&#41; IX&#91;B&#93;
	&#91;9&#93; 0	0	0x000003b0 - 0x000003bb &#40;0xc&#41; IS&#91;B&#93;&#40;OprU&#41;
	&#91;10&#93; 0	0	0x000003c0 - 0x000003df &#40;0x20&#41; IS&#91;B&#93;&#40;OprU&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Kernel reported 231680 total, 1 used
&#40;II&#41; intel&#40;0&#41;&#58; I830CheckAvailableMemory&#58; 926716 kB available
drmOpenDevice&#58; node name is /dev/dri/card0
drmOpenDevice&#58; open result is 12, &#40;OK&#41;
drmOpenDevice&#58; node name is /dev/dri/card0
drmOpenDevice&#58; open result is 12, &#40;OK&#41;
drmOpenByBusid&#58; Searching for BusID pci&#58;0000&#58;00&#58;02.0
drmOpenDevice&#58; node name is /dev/dri/card0
drmOpenDevice&#58; open result is 12, &#40;OK&#41;
drmOpenByBusid&#58; drmOpenMinor returns 12
drmOpenByBusid&#58; drmGetBusid reports pci&#58;0000&#58;00&#58;02.0
&#40;II&#41; &#91;drm&#93; DRM interface version 1.3
&#40;II&#41; &#91;drm&#93; DRM open master succeeded.
&#40;II&#41; intel&#40;0&#41;&#58; &#91;drm&#93; Using the DRM lock SAREA also for drawables.
&#40;II&#41; intel&#40;0&#41;&#58; &#91;drm&#93; framebuffer mapped by ddx driver
&#40;II&#41; intel&#40;0&#41;&#58; &#91;drm&#93; added 1 reserved context for kernel
&#40;II&#41; intel&#40;0&#41;&#58; X context handle = 0x1
&#40;II&#41; intel&#40;0&#41;&#58; &#91;drm&#93; installed DRM signal handler
&#40;**&#41; intel&#40;0&#41;&#58; Framebuffer compression disabled
&#40;**&#41; intel&#40;0&#41;&#58; Tiling enabled
&#40;==&#41; intel&#40;0&#41;&#58; VideoRam&#58; 262144 KB
&#40;II&#41; intel&#40;0&#41;&#58; Attempting memory allocation with tiled buffers.
&#40;II&#41; intel&#40;0&#41;&#58; Tiled allocation successful.
&#40;II&#41; intel&#40;0&#41;&#58; &#91;drm&#93; Registers = 0x50200000
&#40;II&#41; intel&#40;0&#41;&#58; &#91;drm&#93; ring buffer = 0x40000000
&#40;II&#41; intel&#40;0&#41;&#58; &#91;drm&#93; mapped front buffer at 0x41000000, handle = 0x41000000
&#40;II&#41; intel&#40;0&#41;&#58; &#91;drm&#93; mapped back buffer at 0x45000000, handle = 0x45000000
&#40;II&#41; intel&#40;0&#41;&#58; &#91;drm&#93; mapped depth buffer at 0x46000000, handle = 0x46000000
&#40;II&#41; intel&#40;0&#41;&#58; &#91;drm&#93; mapped classic textures at 0x47000000, handle = 0x47000000
&#40;II&#41; intel&#40;0&#41;&#58; &#91;drm&#93; Initialized kernel agp heap manager, 33554432
&#40;II&#41; intel&#40;0&#41;&#58; &#91;dri&#93; visual configs initialized
&#40;II&#41; intel&#40;0&#41;&#58; Page Flipping disabled
&#40;II&#41; intel&#40;0&#41;&#58; vgaHWGetIOBase&#58; hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
&#40;II&#41; EXA&#40;0&#41;&#58; Offscreen pixmap area of 34406400 bytes
&#40;II&#41; EXA&#40;0&#41;&#58; Driver registered support for the following operations&#58;
&#40;II&#41;         Solid
&#40;II&#41;         Copy
&#40;II&#41;         Composite &#40;RENDER acceleration&#41;
&#40;==&#41; intel&#40;0&#41;&#58; Backing store disabled
&#40;==&#41; intel&#40;0&#41;&#58; Silken mouse enabled
&#40;II&#41; intel&#40;0&#41;&#58; Initializing HW Cursor
&#40;II&#41; intel&#40;0&#41;&#58; &#91;DRI&#93; installation complete
&#40;II&#41; intel&#40;0&#41;&#58; Current clock rate multiplier&#58; 1
&#40;II&#41; intel&#40;0&#41;&#58; xf86BindGARTMemory&#58; bind key 0 at 0x01000000 &#40;pgoffset 4096&#41;
&#40;II&#41; intel&#40;0&#41;&#58; xf86BindGARTMemory&#58; bind key 1 at 0x02000000 &#40;pgoffset 8192&#41;
&#40;II&#41; intel&#40;0&#41;&#58; xf86BindGARTMemory&#58; bind key 2 at 0x05000000 &#40;pgoffset 20480&#41;
&#40;II&#41; intel&#40;0&#41;&#58; xf86BindGARTMemory&#58; bind key 3 at 0x06000000 &#40;pgoffset 24576&#41;
&#40;II&#41; intel&#40;0&#41;&#58; xf86BindGARTMemory&#58; bind key 4 at 0x07000000 &#40;pgoffset 28672&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Fixed memory allocation layout&#58;
&#40;II&#41; intel&#40;0&#41;&#58; 0x00000000-0x0001ffff&#58; ring buffer &#40;128 kB&#41;
&#40;II&#41; intel&#40;0&#41;&#58; 0x00020000-0x00029fff&#58; HW cursors &#40;40 kB, 0x000000003f820000 physical
&#41;
&#40;II&#41; intel&#40;0&#41;&#58; 0x0002a000-0x00031fff&#58; logical 3D context &#40;32 kB&#41;
&#40;II&#41; intel&#40;0&#41;&#58; 0x00032000-0x00131fff&#58; fake bufmgr &#40;1024 kB&#41;
&#40;II&#41; intel&#40;0&#41;&#58; 0x00132000-0x00132fff&#58; overlay registers &#40;4 kB, 0x000000003f932000 physical
&#41;
&#40;II&#41; intel&#40;0&#41;&#58; 0x007bf000&#58;            end of stolen memory
&#40;II&#41; intel&#40;0&#41;&#58; 0x01000000-0x01ffffff&#58; front buffer &#40;11200 kB&#41; X tiled
&#40;II&#41; intel&#40;0&#41;&#58; 0x02000000-0x040cffff&#58; exa offscreen &#40;33600 kB&#41;
&#40;II&#41; intel&#40;0&#41;&#58; 0x05000000-0x05ffffff&#58; back buffer &#40;11264 kB&#41; X tiled
&#40;II&#41; intel&#40;0&#41;&#58; 0x06000000-0x06ffffff&#58; depth buffer &#40;11264 kB&#41; X tiled
&#40;II&#41; intel&#40;0&#41;&#58; 0x07000000-0x08ffffff&#58; classic textures &#40;32768 kB&#41;
&#40;II&#41; intel&#40;0&#41;&#58; 0x10000000&#58;            end of aperture
&#40;WW&#41; intel&#40;0&#41;&#58; ESR is 0x00000001, instruction error
&#40;WW&#41; intel&#40;0&#41;&#58; Existing errors found in hardware state.
&#40;II&#41; intel&#40;0&#41;&#58; Output configuration&#58;
&#40;II&#41; intel&#40;0&#41;&#58;   Pipe A is on
&#40;II&#41; intel&#40;0&#41;&#58;   Display plane A is now enabled and connected to pipe A.
&#40;II&#41; intel&#40;0&#41;&#58;   Pipe B is off
&#40;II&#41; intel&#40;0&#41;&#58;   Display plane B is now disabled and connected to pipe B.
&#40;II&#41; intel&#40;0&#41;&#58;   Output VGA is connected to pipe A
&#40;II&#41; intel&#40;0&#41;&#58;   Output TV-1 is connected to pipe none
&#40;II&#41; intel&#40;0&#41;&#58; &#91;drm&#93; dma control initialized, using IRQ 16
&#40;II&#41; intel&#40;0&#41;&#58; RandR 1.2 enabled, ignore the following RandR disabled message.
&#40;II&#41; intel&#40;0&#41;&#58; DPMS enabled
&#40;II&#41; intel&#40;0&#41;&#58; Set up textured video
&#40;II&#41; intel&#40;0&#41;&#58; Set up overlay video
&#40;II&#41; intel&#40;0&#41;&#58; direct rendering&#58; Enabled
&#40;--&#41; RandR disabled
&#40;II&#41; Initializing built-in extension MIT-SHM
&#40;II&#41; Initializing built-in extension XInputExtension
&#40;II&#41; Initializing built-in extension XTEST
&#40;II&#41; Initializing built-in extension XKEYBOARD
&#40;II&#41; Initializing built-in extension XC-APPGROUP
&#40;II&#41; Initializing built-in extension SECURITY
&#40;II&#41; Initializing built-in extension XINERAMA
&#40;II&#41; Initializing built-in extension XFIXES
&#40;II&#41; Initializing built-in extension RENDER
&#40;II&#41; Initializing built-in extension RANDR
&#40;II&#41; Initializing built-in extension COMPOSITE
&#40;II&#41; Initializing built-in extension DAMAGE
&#40;II&#41; Initializing built-in extension XEVIE
drmOpenDevice&#58; node name is /dev/dri/card0
drmOpenDevice&#58; open result is 13, &#40;OK&#41;
drmOpenByBusid&#58; Searching for BusID pci&#58;0000&#58;00&#58;02.0
drmOpenDevice&#58; node name is /dev/dri/card0
drmOpenDevice&#58; open result is 13, &#40;OK&#41;
drmOpenByBusid&#58; drmOpenMinor returns 13
drmOpenByBusid&#58; drmGetBusid reports pci&#58;0000&#58;00&#58;02.0
&#40;II&#41; AIGLX&#58; enabled GLX_MESA_copy_sub_buffer
&#40;II&#41; AIGLX&#58; enabled GLX_SGI_swap_control and GLX_MESA_swap_control
&#40;II&#41; AIGLX&#58; enabled GLX_texture_from_pixmap with driver support
&#40;II&#41; AIGLX&#58; Loaded and initialized /usr/lib/dri/i915_dri.so
&#40;II&#41; GLX&#58; Initialized DRI GL provider for screen 0
&#40;II&#41; intel&#40;0&#41;&#58; Setting screen physical size to 300 x 225
&#40;**&#41; Option "CoreKeyboard"
&#40;**&#41; Keyboard&#91;0&#93;&#58; always reports core events
&#40;**&#41; Option "Protocol" "Standard"
&#40;**&#41; Keyboard&#91;0&#93;&#58; Protocol&#58; Standard
&#40;**&#41; Option "AutoRepeat" "500 30"
&#40;**&#41; Option "XkbRules" "xfree86"
&#40;**&#41; Keyboard&#91;0&#93;&#58; XkbRules&#58; "xfree86"
&#40;**&#41; Option "XkbModel" "microsoftpro"
&#40;**&#41; Keyboard&#91;0&#93;&#58; XkbModel&#58; "microsoftpro"
&#40;**&#41; Option "XkbLayout" "de"
&#40;**&#41; Keyboard&#91;0&#93;&#58; XkbLayout&#58; "de"
&#40;**&#41; Option "XkbVariant" "nodeadkeys"
&#40;**&#41; Keyboard&#91;0&#93;&#58; XkbVariant&#58; "nodeadkeys"
&#40;**&#41; Option "CustomKeycodes" "off"
&#40;**&#41; Keyboard&#91;0&#93;&#58; CustomKeycodes disabled
&#40;**&#41; Option "Protocol" "explorerps/2"
&#40;**&#41; Mouse&#91;1&#93;&#58; Device&#58; "/dev/input/mice"
&#40;**&#41; Mouse&#91;1&#93;&#58; Protocol&#58; "explorerps/2"
&#40;**&#41; Option "CorePointer"
&#40;**&#41; Mouse&#91;1&#93;&#58; always reports core events
&#40;**&#41; Option "Device" "/dev/input/mice"
&#40;**&#41; Option "Buttons" "5"
&#40;==&#41; Mouse&#91;1&#93;&#58; Emulate3Buttons, Emulate3Timeout&#58; 50
&#40;**&#41; Option "ZAxisMapping" "4 5"
&#40;**&#41; Mouse&#91;1&#93;&#58; ZAxisMapping&#58; buttons 4 and 5
&#40;**&#41; Mouse&#91;1&#93;&#58; Buttons&#58; 9
&#40;**&#41; Mouse&#91;1&#93;&#58; Sensitivity&#58; 1
&#40;II&#41; evaluating device &#40;Keyboard&#91;0&#93;&#41;
&#40;II&#41; XINPUT&#58; Adding extended input device "Keyboard&#91;0&#93;" &#40;type&#58; KEYBOARD&#41;
&#40;II&#41; evaluating device &#40;Mouse&#91;1&#93;&#41;
&#40;II&#41; XINPUT&#58; Adding extended input device "Mouse&#91;1&#93;" &#40;type&#58; MOUSE&#41;
&#40;II&#41; Mouse&#91;1&#93;&#58; ps2EnableDataReporting&#58; succeeded
Could not init font path element /usr/share/fonts/TTF/, removing from list!
Could not init font path element /usr/share/fonts/OTF, removing from list!
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "CRTDDC_A" initialized.
&#40;II&#41; intel&#40;0&#41;&#58; I2C device "CRTDDC_A&#58;ddc2" registered at address 0xA0.
&#40;II&#41; intel&#40;0&#41;&#58; I2C device "CRTDDC_A&#58;ddc2" removed.
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "CRTDDC_A" removed.
&#40;II&#41; intel&#40;0&#41;&#58; EDID vendor "SRC", prod id 706
&#40;II&#41; intel&#40;0&#41;&#58; Using hsync ranges from config file
&#40;II&#41; intel&#40;0&#41;&#58; Using vrefresh ranges from config file
&#40;II&#41; intel&#40;0&#41;&#58; Printing DDC gathered Modelines&#58;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x400"x0.0   31.50  640 664 704 832  400 409 412 450 -hsync +vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   94.50  1024 1072 1168 1376  768 769 772 808 +hsync +vsync &#40;68.7 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync &#40;37.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 491 520 -hsync -vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   25.20  640 656 752 800  480 490 492 525 -hsync -vsync &#40;31.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync &#40;31.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   78.80  1024 1040 1136 1312  768 769 772 800 +hsync +vsync &#40;60.1 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync &#40;56.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync &#40;48.4 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync &#40;46.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync &#40;48.1 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1280x1024"x60.0  108.88  1280 1360 1496 1712  1024 1025 1028 1060 -hsync +vsync &#40;63.6 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; EDID vendor "SRC", prod id 706
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "CRTDDC_A" initialized.
&#40;II&#41; intel&#40;0&#41;&#58; I2C device "CRTDDC_A&#58;ddc2" registered at address 0xA0.
&#40;II&#41; intel&#40;0&#41;&#58; I2C device "CRTDDC_A&#58;ddc2" removed.
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "CRTDDC_A" removed.
&#40;II&#41; intel&#40;0&#41;&#58; EDID vendor "SRC", prod id 706
&#40;II&#41; intel&#40;0&#41;&#58; Using hsync ranges from config file
&#40;II&#41; intel&#40;0&#41;&#58; Using vrefresh ranges from config file
&#40;II&#41; intel&#40;0&#41;&#58; Printing DDC gathered Modelines&#58;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x400"x0.0   31.50  640 664 704 832  400 409 412 450 -hsync +vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   94.50  1024 1072 1168 1376  768 769 772 808 +hsync +vsync &#40;68.7 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync &#40;37.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 491 520 -hsync -vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   25.20  640 656 752 800  480 490 492 525 -hsync -vsync &#40;31.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync &#40;31.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   78.80  1024 1040 1136 1312  768 769 772 800 +hsync +vsync &#40;60.1 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync &#40;56.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync &#40;48.4 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync &#40;46.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync &#40;48.1 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1280x1024"x60.0  108.88  1280 1360 1496 1712  1024 1025 1028 1060 -hsync +vsync &#40;63.6 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; EDID vendor "SRC", prod id 706
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "CRTDDC_A" initialized.
&#40;II&#41; intel&#40;0&#41;&#58; I2C device "CRTDDC_A&#58;ddc2" registered at address 0xA0.
&#40;II&#41; intel&#40;0&#41;&#58; I2C device "CRTDDC_A&#58;ddc2" removed.
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "CRTDDC_A" removed.
&#40;II&#41; intel&#40;0&#41;&#58; EDID vendor "SRC", prod id 706
&#40;II&#41; intel&#40;0&#41;&#58; Using hsync ranges from config file
&#40;II&#41; intel&#40;0&#41;&#58; Using vrefresh ranges from config file
&#40;II&#41; intel&#40;0&#41;&#58; Printing DDC gathered Modelines&#58;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x400"x0.0   31.50  640 664 704 832  400 409 412 450 -hsync +vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   94.50  1024 1072 1168 1376  768 769 772 808 +hsync +vsync &#40;68.7 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync &#40;37.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 491 520 -hsync -vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   25.20  640 656 752 800  480 490 492 525 -hsync -vsync &#40;31.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync &#40;31.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   78.80  1024 1040 1136 1312  768 769 772 800 +hsync +vsync &#40;60.1 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync &#40;56.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync &#40;48.4 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync &#40;46.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync &#40;48.1 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1280x1024"x60.0  108.88  1280 1360 1496 1712  1024 1025 1028 1060 -hsync +vsync &#40;63.6 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; EDID vendor "SRC", prod id 706
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "CRTDDC_A" initialized.
&#40;II&#41; intel&#40;0&#41;&#58; I2C device "CRTDDC_A&#58;ddc2" registered at address 0xA0.
&#40;II&#41; intel&#40;0&#41;&#58; I2C device "CRTDDC_A&#58;ddc2" removed.
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "CRTDDC_A" removed.
&#40;II&#41; intel&#40;0&#41;&#58; EDID vendor "SRC", prod id 706
&#40;II&#41; intel&#40;0&#41;&#58; Using hsync ranges from config file
&#40;II&#41; intel&#40;0&#41;&#58; Using vrefresh ranges from config file
&#40;II&#41; intel&#40;0&#41;&#58; Printing DDC gathered Modelines&#58;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x400"x0.0   31.50  640 664 704 832  400 409 412 450 -hsync +vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   94.50  1024 1072 1168 1376  768 769 772 808 +hsync +vsync &#40;68.7 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync &#40;37.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 491 520 -hsync -vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   25.20  640 656 752 800  480 490 492 525 -hsync -vsync &#40;31.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync &#40;31.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   78.80  1024 1040 1136 1312  768 769 772 800 +hsync +vsync &#40;60.1 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync &#40;56.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync &#40;48.4 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync &#40;46.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync &#40;48.1 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1280x1024"x60.0  108.88  1280 1360 1496 1712  1024 1025 1028 1060 -hsync +vsync &#40;63.6 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; EDID vendor "SRC", prod id 706
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "CRTDDC_A" initialized.
&#40;II&#41; intel&#40;0&#41;&#58; I2C device "CRTDDC_A&#58;ddc2" registered at address 0xA0.
&#40;II&#41; intel&#40;0&#41;&#58; I2C device "CRTDDC_A&#58;ddc2" removed.
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "CRTDDC_A" removed.
&#40;II&#41; intel&#40;0&#41;&#58; EDID vendor "SRC", prod id 706
&#40;II&#41; intel&#40;0&#41;&#58; Using hsync ranges from config file
&#40;II&#41; intel&#40;0&#41;&#58; Using vrefresh ranges from config file
&#40;II&#41; intel&#40;0&#41;&#58; Printing DDC gathered Modelines&#58;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x400"x0.0   31.50  640 664 704 832  400 409 412 450 -hsync +vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   94.50  1024 1072 1168 1376  768 769 772 808 +hsync +vsync &#40;68.7 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync &#40;37.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 491 520 -hsync -vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   25.20  640 656 752 800  480 490 492 525 -hsync -vsync &#40;31.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync &#40;31.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   78.80  1024 1040 1136 1312  768 769 772 800 +hsync +vsync &#40;60.1 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync &#40;56.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync &#40;48.4 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync &#40;46.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync &#40;48.1 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1280x1024"x60.0  108.88  1280 1360 1496 1712  1024 1025 1028 1060 -hsync +vsync &#40;63.6 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; EDID vendor "SRC", prod id 706
danke

User avatar
Janka
Posts: 3585
Joined: 11. Feb 2006 19:10

#12 Post by Janka »

Die Datei sieht aus, als wäre sie aus mehreren Teilen zusammengesetzt. Da ist bei Cut+Paste was schiefgegangen.

Janka
Ich vertonne Spam immer in /dev/dsp statt /dev/null.
Ich mag die Schreie.

inixlinux

#13 Post by inixlinux »

ich habe nun nocheinmal den XServer neu gestartet und poste das aktuelle Log, jedoch scheint es mir so als ob es gleich wie das log vorher war, kann mir also nicht vorstellen, dass da beim Copy & Paste was schief ging, hoffe jedoch trotzdem das das log brauchbar ist und der Fehler gefunden wird.

Das log

Code: Select all

_XSERVTransSocketOpenCOTSServer&#58; Unable to open socket for inet6
_XSERVTransOpen&#58; transport open failed for inet6/Server-LB&#58;0
_XSERVTransMakeAllCOTSServerListeners&#58; failed to open listener for inet6

X.Org X Server 1.5.2
Release Date&#58; 10 October 2008
X Protocol Version 11, Revision 0
Build Operating System&#58; openSUSE SUSE LINUX
Current Operating System&#58; Linux Server-LB 2.6.27.42-0.1-pae #1 SMP 2010-01-06 16&#58;07&#58;25 +0100 i686
Build Date&#58; 02 July 2009  08&#58;02&#58;13AM
 
	Before reporting problems, check http&#58;//wiki.x.org
	to make sure that you have the latest version.
Module Loader present
Markers&#58; &#40;--&#41; probed, &#40;**&#41; from config file, &#40;==&#41; default setting,
	&#40;++&#41; from command line, &#40;!!&#41; notice, &#40;II&#41; informational,
	&#40;WW&#41; warning, &#40;EE&#41; error, &#40;NI&#41; not implemented, &#40;??&#41; unknown.
&#40;==&#41; Log file&#58; "/var/log/Xorg.0.log", Time&#58; Sat Jan 23 23&#58;19&#58;06 2010
&#40;==&#41; Using config file&#58; "/etc/X11/xorg.conf"
&#40;==&#41; ServerLayout "Layout&#91;all&#93;"
&#40;**&#41; |-->Screen "Screen&#91;TV&#93;" &#40;0&#41;
&#40;**&#41; |   |-->Monitor "TV"
&#40;**&#41; |   |-->Device "Device&#91;0&#93;"
&#40;EE&#41; Screen Screen&#91;0&#93; doesn't exist&#58; deleting placement
&#40;**&#41; |-->Input Device "Keyboard&#91;0&#93;"
&#40;**&#41; |-->Input Device "Mouse&#91;1&#93;"
&#40;**&#41; Option "ZapWarning" "on"
&#40;**&#41; Option "AllowMouseOpenFail" "on"
&#40;**&#41; Option "Xinerama" "off"
&#40;**&#41; Option "AIGLX" "on"
&#40;==&#41; Automatically adding devices
&#40;==&#41; Automatically enabling devices
&#40;WW&#41; The directory "/usr/share/fonts/local" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/PEX" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/latin2/misc" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/latin2/75dpi" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/latin2/100dpi" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/latin2/Type1" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/latin7/75dpi" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/baekmuk" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/japanese" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/kwintv" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/uni" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/CID" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/ucs/misc" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/ucs/75dpi" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/ucs/100dpi" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/hellas/misc" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/hellas/75dpi" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/hellas/100dpi" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/hellas/Type1" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/misc/sgi" does not exist.
	Entry deleted from font path.
&#40;WW&#41; The directory "/usr/share/fonts/xtest" does not exist.
	Entry deleted from font path.
&#40;==&#41; Including the default font path /usr/share/fonts/misc&#58;unscaled,/usr/share/fonts/TTF/,/usr/share/fonts/OTF,/usr/share/fonts/Type1/,/usr/share/fonts/100dpi&#58;unscaled,/usr/share/fonts/75dpi&#58;unscaled.
&#40;**&#41; FontPath set to&#58;
	/usr/share/fonts/misc&#58;unscaled,
	/usr/share/fonts/75dpi&#58;unscaled,
	/usr/share/fonts/100dpi&#58;unscaled,
	/usr/share/fonts/Type1,
	/usr/share/fonts/URW,
	/usr/share/fonts/Speedo,
	/usr/share/fonts/cyrillic,
	/usr/share/fonts/truetype,
	/opt/kde3/share/fonts,
	/usr/share/fonts/misc&#58;unscaled,
	/usr/share/fonts/TTF/,
	/usr/share/fonts/OTF,
	/usr/share/fonts/Type1/,
	/usr/share/fonts/100dpi&#58;unscaled,
	/usr/share/fonts/75dpi&#58;unscaled
&#40;**&#41; Input device list set to "/dev/gpmdata,/dev/input/mice"
&#40;==&#41; ModulePath set to "/usr/lib/xorg/modules/updates,/usr/lib/xorg/modules"
&#40;II&#41; Open ACPI successful &#40;/var/run/acpid.socket&#41;
&#40;II&#41; Loader magic&#58; 0x81f95c0
&#40;II&#41; Module ABI versions&#58;
	X.Org ANSI C Emulation&#58; 0.4
	X.Org Video Driver&#58; 4.1
	X.Org XInput driver &#58; 2.1
	X.Org Server Extension &#58; 1.1
	X.Org Font Renderer &#58; 0.6
&#40;II&#41; Loader running on linux
&#40;++&#41; using VT number 7

&#40;--&#41; PCI&#58;*&#40;0@0&#58;2&#58;0&#41; unknown vendor &#40;0x8086&#41; unknown chipset &#40;0x2772&#41; rev 2, Mem @ 0x50200000/0, 0x40000000/0, 0x50280000/0, I/O @ 0x000020e0/0
&#40;II&#41; System resource ranges&#58;
	&#91;0&#93; -1	0	0xffffffff - 0xffffffff &#40;0x1&#41; MX&#91;B&#93;
	&#91;1&#93; -1	0	0x000f0000 - 0x000fffff &#40;0x10000&#41; MX&#91;B&#93;
	&#91;2&#93; -1	0	0x000c0000 - 0x000effff &#40;0x30000&#41; MX&#91;B&#93;
	&#91;3&#93; -1	0	0x00000000 - 0x0009ffff &#40;0xa0000&#41; MX&#91;B&#93;
	&#91;4&#93; -1	0	0x0000ffff - 0x0000ffff &#40;0x1&#41; IX&#91;B&#93;
	&#91;5&#93; -1	0	0x00000000 - 0x00000000 &#40;0x1&#41; IX&#91;B&#93;
&#40;II&#41; "extmod" will be loaded. This was enabled by default and also specified in the config file.
&#40;II&#41; "dbe" will be loaded. This was enabled by default and also specified in the config file.
&#40;II&#41; "glx" will be loaded. This was enabled by default and also specified in the config file.
&#40;II&#41; "freetype" will be loaded. This was enabled by default and also specified in the config file.
&#40;II&#41; "record" will be loaded by default.
&#40;II&#41; "dri" will be loaded. This was enabled by default and also specified in the config file.
&#40;II&#41; LoadModule&#58; "glx"

&#40;II&#41; Loading /usr/lib/xorg/modules//extensions/libglx.so
&#40;II&#41; Module glx&#58; vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 1.0.0
	ABI class&#58; X.Org Server Extension, version 1.1
&#40;**&#41; AIGLX enabled
&#40;**&#41; Exporting typical set of GLX visuals
&#40;II&#41; Loading extension GLX
&#40;II&#41; LoadModule&#58; "dbe"

&#40;II&#41; Loading /usr/lib/xorg/modules//extensions/libdbe.so
&#40;II&#41; Module dbe&#58; vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 1.0.0
	Module class&#58; X.Org Server Extension
	ABI class&#58; X.Org Server Extension, version 1.1
&#40;II&#41; Loading extension DOUBLE-BUFFER
&#40;II&#41; LoadModule&#58; "extmod"

&#40;II&#41; Loading /usr/lib/xorg/modules//extensions/libextmod.so
&#40;II&#41; Module extmod&#58; vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 1.0.0
	Module class&#58; X.Org Server Extension
	ABI class&#58; X.Org Server Extension, version 1.1
&#40;II&#41; Loading extension SHAPE
&#40;II&#41; Loading extension MIT-SUNDRY-NONSTANDARD
&#40;II&#41; Loading extension BIG-REQUESTS
&#40;II&#41; Loading extension SYNC
&#40;II&#41; Loading extension MIT-SCREEN-SAVER
&#40;II&#41; Loading extension XC-MISC
&#40;II&#41; Loading extension XFree86-VidModeExtension
&#40;II&#41; Loading extension XFree86-Misc
&#40;II&#41; Loading extension XFree86-DGA
&#40;II&#41; Loading extension DPMS
&#40;II&#41; Loading extension TOG-CUP
&#40;II&#41; Loading extension Extended-Visual-Information
&#40;II&#41; Loading extension XVideo
&#40;II&#41; Loading extension XVideo-MotionCompensation
&#40;II&#41; Loading extension X-Resource
&#40;II&#41; LoadModule&#58; "freetype"

&#40;II&#41; Loading /usr/lib/xorg/modules//fonts/libfreetype.so
&#40;II&#41; Module freetype&#58; vendor="X.Org Foundation & the After X-TT Project"
	compiled for 1.5.2, module version = 2.1.0
	Module class&#58; X.Org Font Renderer
	ABI class&#58; X.Org Font Renderer, version 0.6
&#40;II&#41; Loading font FreeType
&#40;II&#41; LoadModule&#58; "dri"

&#40;II&#41; Loading /usr/lib/xorg/modules//extensions/libdri.so
&#40;II&#41; Module dri&#58; vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 1.0.0
	ABI class&#58; X.Org Server Extension, version 1.1
&#40;II&#41; Loading extension XFree86-DRI
&#40;II&#41; LoadModule&#58; "record"

&#40;II&#41; Loading /usr/lib/xorg/modules//extensions/librecord.so
&#40;II&#41; Module record&#58; vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 1.13.0
	Module class&#58; X.Org Server Extension
	ABI class&#58; X.Org Server Extension, version 1.1
&#40;II&#41; Loading extension RECORD
&#40;II&#41; LoadModule&#58; "intel"

&#40;II&#41; Loading /usr/lib/xorg/modules//drivers/intel_drv.so
&#40;II&#41; Module intel&#58; vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 2.5.0
	Module class&#58; X.Org Video Driver
	ABI class&#58; X.Org Video Driver, version 4.1
&#40;II&#41; LoadModule&#58; "kbd"

&#40;II&#41; Loading /usr/lib/xorg/modules//input/kbd_drv.so
&#40;II&#41; Module kbd&#58; vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 1.3.1
	Module class&#58; X.Org XInput Driver
	ABI class&#58; X.Org XInput driver, version 2.1
&#40;II&#41; LoadModule&#58; "mouse"

&#40;II&#41; Loading /usr/lib/xorg/modules//input/mouse_drv.so
&#40;II&#41; Module mouse&#58; vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 1.3.0
	Module class&#58; X.Org XInput Driver
	ABI class&#58; X.Org XInput driver, version 2.1
&#40;II&#41; intel&#58; Driver for Intel Integrated Graphics Chipsets&#58; i810,
	i810-dc100, i810e, i815, i830M, 845G, 852GM/855GM, 865G, 915G,
	E7221 &#40;i915&#41;, 915GM, 945G, 945GM, 945GME, 965G, G35, 965Q, 946GZ,
	965GM, 965GME/GLE, G33, Q35, Q33,
	Mobile Intel® GM45 Express Chipset,
	Intel Integrated Graphics Device, G45/G43, Q45/Q43, G41
&#40;II&#41; Primary Device is&#58; PCI 00@00&#58;02&#58;0
&#40;II&#41; resource ranges after xf86ClaimFixedResources&#40;&#41; call&#58;
	&#91;0&#93; -1	0	0xffffffff - 0xffffffff &#40;0x1&#41; MX&#91;B&#93;
	&#91;1&#93; -1	0	0x000f0000 - 0x000fffff &#40;0x10000&#41; MX&#91;B&#93;
	&#91;2&#93; -1	0	0x000c0000 - 0x000effff &#40;0x30000&#41; MX&#91;B&#93;
	&#91;3&#93; -1	0	0x00000000 - 0x0009ffff &#40;0xa0000&#41; MX&#91;B&#93;
	&#91;4&#93; -1	0	0x0000ffff - 0x0000ffff &#40;0x1&#41; IX&#91;B&#93;
	&#91;5&#93; -1	0	0x00000000 - 0x00000000 &#40;0x1&#41; IX&#91;B&#93;
&#40;II&#41; resource ranges after probing&#58;
	&#91;0&#93; -1	0	0xffffffff - 0xffffffff &#40;0x1&#41; MX&#91;B&#93;
	&#91;1&#93; -1	0	0x000f0000 - 0x000fffff &#40;0x10000&#41; MX&#91;B&#93;
	&#91;2&#93; -1	0	0x000c0000 - 0x000effff &#40;0x30000&#41; MX&#91;B&#93;
	&#91;3&#93; -1	0	0x00000000 - 0x0009ffff &#40;0xa0000&#41; MX&#91;B&#93;
	&#91;4&#93; 0	0	0x000a0000 - 0x000affff &#40;0x10000&#41; MS&#91;B&#93;
	&#91;5&#93; 0	0	0x000b0000 - 0x000b7fff &#40;0x8000&#41; MS&#91;B&#93;
	&#91;6&#93; 0	0	0x000b8000 - 0x000bffff &#40;0x8000&#41; MS&#91;B&#93;
	&#91;7&#93; -1	0	0x0000ffff - 0x0000ffff &#40;0x1&#41; IX&#91;B&#93;
	&#91;8&#93; -1	0	0x00000000 - 0x00000000 &#40;0x1&#41; IX&#91;B&#93;
	&#91;9&#93; 0	0	0x000003b0 - 0x000003bb &#40;0xc&#41; IS&#91;B&#93;
	&#91;10&#93; 0	0	0x000003c0 - 0x000003df &#40;0x20&#41; IS&#91;B&#93;
&#40;II&#41; Loading sub module "vgahw"
&#40;II&#41; LoadModule&#58; "vgahw"

&#40;II&#41; Loading /usr/lib/xorg/modules//libvgahw.so
&#40;II&#41; Module vgahw&#58; vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 0.1.0
	ABI class&#58; X.Org Video Driver, version 4.1
&#40;**&#41; intel&#40;0&#41;&#58; Depth 24, &#40;--&#41; framebuffer bpp 32
&#40;==&#41; intel&#40;0&#41;&#58; RGB weight 888
&#40;==&#41; intel&#40;0&#41;&#58; Default visual is TrueColor
&#40;II&#41; intel&#40;0&#41;&#58; Integrated Graphics Chipset&#58; Intel&#40;R&#41; 945G
&#40;--&#41; intel&#40;0&#41;&#58; Chipset&#58; "945G"
&#40;--&#41; intel&#40;0&#41;&#58; Linear framebuffer at 0x40000000
&#40;--&#41; intel&#40;0&#41;&#58; IO registers at addr 0x50200000
&#40;WW&#41; intel&#40;0&#41;&#58; libpciaccess reported 0 rom size, guessing 64kB
&#40;==&#41; intel&#40;0&#41;&#58; Using EXA for acceleration
&#40;II&#41; intel&#40;0&#41;&#58; 2 display pipes available.
&#40;II&#41; Loading sub module "ddc"
&#40;II&#41; LoadModule&#58; "ddc"
&#40;II&#41; Module "ddc" already built-in
&#40;II&#41; Loading sub module "i2c"
&#40;II&#41; LoadModule&#58; "i2c"
&#40;II&#41; Module "i2c" already built-in
&#40;II&#41; intel&#40;0&#41;&#58; Output VGA using monitor section EXT1
&#40;**&#41; intel&#40;0&#41;&#58; Option "PreferredMode" "1280x1024"
&#40;**&#41; intel&#40;0&#41;&#58; Option "Ignore" "false"
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "SDVOCTRL_E for SDVOB" initialized.
&#40;II&#41; intel&#40;0&#41;&#58; I2C device "SDVOCTRL_E for SDVOB&#58;SDVO Controller B" registered at address 0x70.
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "SDVOB DDC Bus" initialized.
&#40;II&#41; intel&#40;0&#41;&#58; Output TV-1 using monitor section TV
&#40;II&#41; intel&#40;0&#41;&#58; SDVOB&#58; device VID/DID&#58; 02&#58;C2.02, clock range 25.0MHz - 160.0MHz
&#40;II&#41; intel&#40;0&#41;&#58; SDVOB&#58; 1 input channel
&#40;II&#41; intel&#40;0&#41;&#58; SDVOB&#58; RGB0 output reported
&#40;II&#41; intel&#40;0&#41;&#58; SDVOB&#58; CVBS0 output reported
&#40;II&#41; intel&#40;0&#41;&#58; SDVOB&#58; SVID0 output reported
&#40;II&#41; intel&#40;0&#41;&#58; SDVOB&#58; YPRPB0 output reported
&#40;II&#41; intel&#40;0&#41;&#58; SDVOB&#58; SCART0 output reported
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "SDVOCTRL_E for SDVOC" initialized.
&#40;II&#41; intel&#40;0&#41;&#58; I2C device "SDVOCTRL_E for SDVOC&#58;SDVO Controller C" registered at address 0x72.
&#40;II&#41; intel&#40;0&#41;&#58; No SDVO device found on SDVOC
&#40;II&#41; intel&#40;0&#41;&#58; I2C device "SDVOCTRL_E for SDVOC&#58;SDVO Controller C" removed.
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "SDVOCTRL_E for SDVOC" removed.
&#40;II&#41; intel&#40;0&#41;&#58; Output VGA using monitor section EXT1
&#40;II&#41; intel&#40;0&#41;&#58; Current clock rate multiplier&#58; 1
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "CRTDDC_A" initialized.
&#40;II&#41; intel&#40;0&#41;&#58; I2C device "CRTDDC_A&#58;ddc2" registered at address 0xA0.
&#40;II&#41; intel&#40;0&#41;&#58; I2C device "CRTDDC_A&#58;ddc2" removed.
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "CRTDDC_A" removed.
&#40;II&#41; intel&#40;0&#41;&#58; EDID vendor "SRC", prod id 706
&#40;II&#41; intel&#40;0&#41;&#58; Using hsync ranges from config file
&#40;II&#41; intel&#40;0&#41;&#58; Using vrefresh ranges from config file
&#40;II&#41; intel&#40;0&#41;&#58; Printing DDC gathered Modelines&#58;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x400"x0.0   31.50  640 664 704 832  400 409 412 450 -hsync +vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   94.50  1024 1072 1168 1376  768 769 772 808 +hsync +vsync &#40;68.7 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync &#40;37.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 491 520 -hsync -vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   25.20  640 656 752 800  480 490 492 525 -hsync -vsync &#40;31.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync &#40;31.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   78.80  1024 1040 1136 1312  768 769 772 800 +hsync +vsync &#40;60.1 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync &#40;56.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync &#40;48.4 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync &#40;46.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync &#40;48.1 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1280x1024"x60.0  108.88  1280 1360 1496 1712  1024 1025 1028 1060 -hsync +vsync &#40;63.6 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; EDID vendor "SRC", prod id 706
&#40;II&#41; intel&#40;0&#41;&#58; Output TV-1 using monitor section TV
&#40;II&#41; intel&#40;0&#41;&#58; Output VGA connected
&#40;II&#41; intel&#40;0&#41;&#58; Output TV-1 connected
&#40;II&#41; intel&#40;0&#41;&#58; Using user preference for initial modes
&#40;II&#41; intel&#40;0&#41;&#58; Output VGA using initial mode 1280x1024
&#40;EE&#41; intel&#40;0&#41;&#58; Output TV-1 enabled but has no modes
&#40;II&#41; intel&#40;0&#41;&#58; detected 256 kB GTT.
&#40;II&#41; intel&#40;0&#41;&#58; detected 7932 kB stolen memory.
&#40;==&#41; intel&#40;0&#41;&#58; video overlay key set to 0x101fe
&#40;==&#41; intel&#40;0&#41;&#58; Intel XvMC decoder disabled
&#40;==&#41; intel&#40;0&#41;&#58; Will not try to enable page flipping
&#40;==&#41; intel&#40;0&#41;&#58; Triple buffering disabled
&#40;==&#41; intel&#40;0&#41;&#58; Using gamma correction &#40;1.0, 1.0, 1.0&#41;
&#40;**&#41; intel&#40;0&#41;&#58; Display dimensions&#58; &#40;320, 240&#41; mm
&#40;**&#41; intel&#40;0&#41;&#58; DPI set to &#40;101, 108&#41;
&#40;II&#41; Loading sub module "fb"
&#40;II&#41; LoadModule&#58; "fb"

&#40;II&#41; Loading /usr/lib/xorg/modules//libfb.so
&#40;II&#41; Module fb&#58; vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 1.0.0
	ABI class&#58; X.Org ANSI C Emulation, version 0.4
&#40;II&#41; Loading sub module "exa"
&#40;II&#41; LoadModule&#58; "exa"

&#40;II&#41; Loading /usr/lib/xorg/modules//libexa.so
&#40;II&#41; Module exa&#58; vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 2.4.0
	ABI class&#58; X.Org Video Driver, version 4.1
&#40;II&#41; Loading sub module "ramdac"
&#40;II&#41; LoadModule&#58; "ramdac"
&#40;II&#41; Module "ramdac" already built-in
&#40;II&#41; intel&#40;0&#41;&#58; Comparing regs from server start up to After PreInit
&#40;==&#41; Depth 24 pixmap format is 32 bpp
&#40;II&#41; do I need RAC?  No, I don't.
&#40;II&#41; resource ranges after preInit&#58;
	&#91;0&#93; -1	0	0xffffffff - 0xffffffff &#40;0x1&#41; MX&#91;B&#93;
	&#91;1&#93; -1	0	0x000f0000 - 0x000fffff &#40;0x10000&#41; MX&#91;B&#93;
	&#91;2&#93; -1	0	0x000c0000 - 0x000effff &#40;0x30000&#41; MX&#91;B&#93;
	&#91;3&#93; -1	0	0x00000000 - 0x0009ffff &#40;0xa0000&#41; MX&#91;B&#93;
	&#91;4&#93; 0	0	0x000a0000 - 0x000affff &#40;0x10000&#41; MS&#91;B&#93;&#40;OprD&#41;
	&#91;5&#93; 0	0	0x000b0000 - 0x000b7fff &#40;0x8000&#41; MS&#91;B&#93;&#40;OprD&#41;
	&#91;6&#93; 0	0	0x000b8000 - 0x000bffff &#40;0x8000&#41; MS&#91;B&#93;&#40;OprD&#41;
	&#91;7&#93; -1	0	0x0000ffff - 0x0000ffff &#40;0x1&#41; IX&#91;B&#93;
	&#91;8&#93; -1	0	0x00000000 - 0x00000000 &#40;0x1&#41; IX&#91;B&#93;
	&#91;9&#93; 0	0	0x000003b0 - 0x000003bb &#40;0xc&#41; IS&#91;B&#93;&#40;OprU&#41;
	&#91;10&#93; 0	0	0x000003c0 - 0x000003df &#40;0x20&#41; IS&#91;B&#93;&#40;OprU&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Kernel reported 231680 total, 1 used
&#40;II&#41; intel&#40;0&#41;&#58; I830CheckAvailableMemory&#58; 926716 kB available
drmOpenDevice&#58; node name is /dev/dri/card0
drmOpenDevice&#58; open result is 12, &#40;OK&#41;
drmOpenDevice&#58; node name is /dev/dri/card0
drmOpenDevice&#58; open result is 12, &#40;OK&#41;
drmOpenByBusid&#58; Searching for BusID pci&#58;0000&#58;00&#58;02.0
drmOpenDevice&#58; node name is /dev/dri/card0
drmOpenDevice&#58; open result is 12, &#40;OK&#41;
drmOpenByBusid&#58; drmOpenMinor returns 12
drmOpenByBusid&#58; drmGetBusid reports pci&#58;0000&#58;00&#58;02.0
&#40;II&#41; &#91;drm&#93; DRM interface version 1.3
&#40;II&#41; &#91;drm&#93; DRM open master succeeded.
&#40;II&#41; intel&#40;0&#41;&#58; &#91;drm&#93; Using the DRM lock SAREA also for drawables.
&#40;II&#41; intel&#40;0&#41;&#58; &#91;drm&#93; framebuffer mapped by ddx driver
&#40;II&#41; intel&#40;0&#41;&#58; &#91;drm&#93; added 1 reserved context for kernel
&#40;II&#41; intel&#40;0&#41;&#58; X context handle = 0x1
&#40;II&#41; intel&#40;0&#41;&#58; &#91;drm&#93; installed DRM signal handler
&#40;**&#41; intel&#40;0&#41;&#58; Framebuffer compression disabled
&#40;**&#41; intel&#40;0&#41;&#58; Tiling enabled
&#40;==&#41; intel&#40;0&#41;&#58; VideoRam&#58; 262144 KB
&#40;II&#41; intel&#40;0&#41;&#58; Attempting memory allocation with tiled buffers.
&#40;II&#41; intel&#40;0&#41;&#58; Tiled allocation successful.
&#40;II&#41; intel&#40;0&#41;&#58; &#91;drm&#93; Registers = 0x50200000
&#40;II&#41; intel&#40;0&#41;&#58; &#91;drm&#93; ring buffer = 0x40000000
&#40;II&#41; intel&#40;0&#41;&#58; &#91;drm&#93; mapped front buffer at 0x41000000, handle = 0x41000000
&#40;II&#41; intel&#40;0&#41;&#58; &#91;drm&#93; mapped back buffer at 0x45000000, handle = 0x45000000
&#40;II&#41; intel&#40;0&#41;&#58; &#91;drm&#93; mapped depth buffer at 0x46000000, handle = 0x46000000
&#40;II&#41; intel&#40;0&#41;&#58; &#91;drm&#93; mapped classic textures at 0x47000000, handle = 0x47000000
&#40;II&#41; intel&#40;0&#41;&#58; &#91;drm&#93; Initialized kernel agp heap manager, 33554432
&#40;II&#41; intel&#40;0&#41;&#58; &#91;dri&#93; visual configs initialized
&#40;II&#41; intel&#40;0&#41;&#58; Page Flipping disabled
&#40;II&#41; intel&#40;0&#41;&#58; vgaHWGetIOBase&#58; hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
&#40;II&#41; EXA&#40;0&#41;&#58; Offscreen pixmap area of 34406400 bytes
&#40;II&#41; EXA&#40;0&#41;&#58; Driver registered support for the following operations&#58;
&#40;II&#41;         Solid
&#40;II&#41;         Copy
&#40;II&#41;         Composite &#40;RENDER acceleration&#41;
&#40;==&#41; intel&#40;0&#41;&#58; Backing store disabled
&#40;==&#41; intel&#40;0&#41;&#58; Silken mouse enabled
&#40;II&#41; intel&#40;0&#41;&#58; Initializing HW Cursor
&#40;II&#41; intel&#40;0&#41;&#58; &#91;DRI&#93; installation complete
&#40;II&#41; intel&#40;0&#41;&#58; Current clock rate multiplier&#58; 1
&#40;II&#41; intel&#40;0&#41;&#58; xf86BindGARTMemory&#58; bind key 0 at 0x01000000 &#40;pgoffset 4096&#41;
&#40;II&#41; intel&#40;0&#41;&#58; xf86BindGARTMemory&#58; bind key 1 at 0x02000000 &#40;pgoffset 8192&#41;
&#40;II&#41; intel&#40;0&#41;&#58; xf86BindGARTMemory&#58; bind key 2 at 0x05000000 &#40;pgoffset 20480&#41;
&#40;II&#41; intel&#40;0&#41;&#58; xf86BindGARTMemory&#58; bind key 3 at 0x06000000 &#40;pgoffset 24576&#41;
&#40;II&#41; intel&#40;0&#41;&#58; xf86BindGARTMemory&#58; bind key 4 at 0x07000000 &#40;pgoffset 28672&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Fixed memory allocation layout&#58;
&#40;II&#41; intel&#40;0&#41;&#58; 0x00000000-0x0001ffff&#58; ring buffer &#40;128 kB&#41;
&#40;II&#41; intel&#40;0&#41;&#58; 0x00020000-0x00029fff&#58; HW cursors &#40;40 kB, 0x000000003f820000 physical
&#41;
&#40;II&#41; intel&#40;0&#41;&#58; 0x0002a000-0x00031fff&#58; logical 3D context &#40;32 kB&#41;
&#40;II&#41; intel&#40;0&#41;&#58; 0x00032000-0x00131fff&#58; fake bufmgr &#40;1024 kB&#41;
&#40;II&#41; intel&#40;0&#41;&#58; 0x00132000-0x00132fff&#58; overlay registers &#40;4 kB, 0x000000003f932000 physical
&#41;
&#40;II&#41; intel&#40;0&#41;&#58; 0x007bf000&#58;            end of stolen memory
&#40;II&#41; intel&#40;0&#41;&#58; 0x01000000-0x01ffffff&#58; front buffer &#40;11200 kB&#41; X tiled
&#40;II&#41; intel&#40;0&#41;&#58; 0x02000000-0x040cffff&#58; exa offscreen &#40;33600 kB&#41;
&#40;II&#41; intel&#40;0&#41;&#58; 0x05000000-0x05ffffff&#58; back buffer &#40;11264 kB&#41; X tiled
&#40;II&#41; intel&#40;0&#41;&#58; 0x06000000-0x06ffffff&#58; depth buffer &#40;11264 kB&#41; X tiled
&#40;II&#41; intel&#40;0&#41;&#58; 0x07000000-0x08ffffff&#58; classic textures &#40;32768 kB&#41;
&#40;II&#41; intel&#40;0&#41;&#58; 0x10000000&#58;            end of aperture
&#40;WW&#41; intel&#40;0&#41;&#58; ESR is 0x00000001, instruction error
&#40;WW&#41; intel&#40;0&#41;&#58; Existing errors found in hardware state.
&#40;II&#41; intel&#40;0&#41;&#58; Output configuration&#58;
&#40;II&#41; intel&#40;0&#41;&#58;   Pipe A is on
&#40;II&#41; intel&#40;0&#41;&#58;   Display plane A is now enabled and connected to pipe A.
&#40;II&#41; intel&#40;0&#41;&#58;   Pipe B is off
&#40;II&#41; intel&#40;0&#41;&#58;   Display plane B is now disabled and connected to pipe B.
&#40;II&#41; intel&#40;0&#41;&#58;   Output VGA is connected to pipe A
&#40;II&#41; intel&#40;0&#41;&#58;   Output TV-1 is connected to pipe none
&#40;II&#41; intel&#40;0&#41;&#58; &#91;drm&#93; dma control initialized, using IRQ 16
&#40;II&#41; intel&#40;0&#41;&#58; RandR 1.2 enabled, ignore the following RandR disabled message.
&#40;II&#41; intel&#40;0&#41;&#58; DPMS enabled
&#40;II&#41; intel&#40;0&#41;&#58; Set up textured video
&#40;II&#41; intel&#40;0&#41;&#58; Set up overlay video
&#40;II&#41; intel&#40;0&#41;&#58; direct rendering&#58; Enabled
&#40;--&#41; RandR disabled
&#40;II&#41; Initializing built-in extension MIT-SHM
&#40;II&#41; Initializing built-in extension XInputExtension
&#40;II&#41; Initializing built-in extension XTEST
&#40;II&#41; Initializing built-in extension XKEYBOARD
&#40;II&#41; Initializing built-in extension XC-APPGROUP
&#40;II&#41; Initializing built-in extension SECURITY
&#40;II&#41; Initializing built-in extension XINERAMA
&#40;II&#41; Initializing built-in extension XFIXES
&#40;II&#41; Initializing built-in extension RENDER
&#40;II&#41; Initializing built-in extension RANDR
&#40;II&#41; Initializing built-in extension COMPOSITE
&#40;II&#41; Initializing built-in extension DAMAGE
&#40;II&#41; Initializing built-in extension XEVIE
drmOpenDevice&#58; node name is /dev/dri/card0
drmOpenDevice&#58; open result is 13, &#40;OK&#41;
drmOpenByBusid&#58; Searching for BusID pci&#58;0000&#58;00&#58;02.0
drmOpenDevice&#58; node name is /dev/dri/card0
drmOpenDevice&#58; open result is 13, &#40;OK&#41;
drmOpenByBusid&#58; drmOpenMinor returns 13
drmOpenByBusid&#58; drmGetBusid reports pci&#58;0000&#58;00&#58;02.0
&#40;II&#41; AIGLX&#58; enabled GLX_MESA_copy_sub_buffer
&#40;II&#41; AIGLX&#58; enabled GLX_SGI_swap_control and GLX_MESA_swap_control
&#40;II&#41; AIGLX&#58; enabled GLX_texture_from_pixmap with driver support
&#40;II&#41; AIGLX&#58; Loaded and initialized /usr/lib/dri/i915_dri.so
&#40;II&#41; GLX&#58; Initialized DRI GL provider for screen 0
&#40;II&#41; intel&#40;0&#41;&#58; Setting screen physical size to 300 x 225
&#40;**&#41; Option "CoreKeyboard"
&#40;**&#41; Keyboard&#91;0&#93;&#58; always reports core events
&#40;**&#41; Option "Protocol" "Standard"
&#40;**&#41; Keyboard&#91;0&#93;&#58; Protocol&#58; Standard
&#40;**&#41; Option "AutoRepeat" "500 30"
&#40;**&#41; Option "XkbRules" "xfree86"
&#40;**&#41; Keyboard&#91;0&#93;&#58; XkbRules&#58; "xfree86"
&#40;**&#41; Option "XkbModel" "microsoftpro"
&#40;**&#41; Keyboard&#91;0&#93;&#58; XkbModel&#58; "microsoftpro"
&#40;**&#41; Option "XkbLayout" "de"
&#40;**&#41; Keyboard&#91;0&#93;&#58; XkbLayout&#58; "de"
&#40;**&#41; Option "XkbVariant" "nodeadkeys"
&#40;**&#41; Keyboard&#91;0&#93;&#58; XkbVariant&#58; "nodeadkeys"
&#40;**&#41; Option "CustomKeycodes" "off"
&#40;**&#41; Keyboard&#91;0&#93;&#58; CustomKeycodes disabled
&#40;**&#41; Option "Protocol" "explorerps/2"
&#40;**&#41; Mouse&#91;1&#93;&#58; Device&#58; "/dev/input/mice"
&#40;**&#41; Mouse&#91;1&#93;&#58; Protocol&#58; "explorerps/2"
&#40;**&#41; Option "CorePointer"
&#40;**&#41; Mouse&#91;1&#93;&#58; always reports core events
&#40;**&#41; Option "Device" "/dev/input/mice"
&#40;**&#41; Option "Buttons" "5"
&#40;==&#41; Mouse&#91;1&#93;&#58; Emulate3Buttons, Emulate3Timeout&#58; 50
&#40;**&#41; Option "ZAxisMapping" "4 5"
&#40;**&#41; Mouse&#91;1&#93;&#58; ZAxisMapping&#58; buttons 4 and 5
&#40;**&#41; Mouse&#91;1&#93;&#58; Buttons&#58; 9
&#40;**&#41; Mouse&#91;1&#93;&#58; Sensitivity&#58; 1
&#40;II&#41; evaluating device &#40;Keyboard&#91;0&#93;&#41;
&#40;II&#41; XINPUT&#58; Adding extended input device "Keyboard&#91;0&#93;" &#40;type&#58; KEYBOARD&#41;
&#40;II&#41; evaluating device &#40;Mouse&#91;1&#93;&#41;
&#40;II&#41; XINPUT&#58; Adding extended input device "Mouse&#91;1&#93;" &#40;type&#58; MOUSE&#41;
&#40;II&#41; Mouse&#91;1&#93;&#58; ps2EnableDataReporting&#58; succeeded
Could not init font path element /usr/share/fonts/TTF/, removing from list!
Could not init font path element /usr/share/fonts/OTF, removing from list!
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "CRTDDC_A" initialized.
&#40;II&#41; intel&#40;0&#41;&#58; I2C device "CRTDDC_A&#58;ddc2" registered at address 0xA0.
&#40;II&#41; intel&#40;0&#41;&#58; I2C device "CRTDDC_A&#58;ddc2" removed.
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "CRTDDC_A" removed.
&#40;II&#41; intel&#40;0&#41;&#58; EDID vendor "SRC", prod id 706
&#40;II&#41; intel&#40;0&#41;&#58; Using hsync ranges from config file
&#40;II&#41; intel&#40;0&#41;&#58; Using vrefresh ranges from config file
&#40;II&#41; intel&#40;0&#41;&#58; Printing DDC gathered Modelines&#58;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x400"x0.0   31.50  640 664 704 832  400 409 412 450 -hsync +vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   94.50  1024 1072 1168 1376  768 769 772 808 +hsync +vsync &#40;68.7 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync &#40;37.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 491 520 -hsync -vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   25.20  640 656 752 800  480 490 492 525 -hsync -vsync &#40;31.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync &#40;31.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   78.80  1024 1040 1136 1312  768 769 772 800 +hsync +vsync &#40;60.1 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync &#40;56.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync &#40;48.4 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync &#40;46.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync &#40;48.1 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1280x1024"x60.0  108.88  1280 1360 1496 1712  1024 1025 1028 1060 -hsync +vsync &#40;63.6 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; EDID vendor "SRC", prod id 706
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "CRTDDC_A" initialized.
&#40;II&#41; intel&#40;0&#41;&#58; I2C device "CRTDDC_A&#58;ddc2" registered at address 0xA0.
&#40;II&#41; intel&#40;0&#41;&#58; I2C device "CRTDDC_A&#58;ddc2" removed.
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "CRTDDC_A" removed.
&#40;II&#41; intel&#40;0&#41;&#58; EDID vendor "SRC", prod id 706
&#40;II&#41; intel&#40;0&#41;&#58; Using hsync ranges from config file
&#40;II&#41; intel&#40;0&#41;&#58; Using vrefresh ranges from config file
&#40;II&#41; intel&#40;0&#41;&#58; Printing DDC gathered Modelines&#58;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x400"x0.0   31.50  640 664 704 832  400 409 412 450 -hsync +vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   94.50  1024 1072 1168 1376  768 769 772 808 +hsync +vsync &#40;68.7 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync &#40;37.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 491 520 -hsync -vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   25.20  640 656 752 800  480 490 492 525 -hsync -vsync &#40;31.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync &#40;31.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   78.80  1024 1040 1136 1312  768 769 772 800 +hsync +vsync &#40;60.1 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync &#40;56.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync &#40;48.4 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync &#40;46.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync &#40;48.1 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1280x1024"x60.0  108.88  1280 1360 1496 1712  1024 1025 1028 1060 -hsync +vsync &#40;63.6 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; EDID vendor "SRC", prod id 706
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "CRTDDC_A" initialized.
&#40;II&#41; intel&#40;0&#41;&#58; I2C device "CRTDDC_A&#58;ddc2" registered at address 0xA0.
&#40;II&#41; intel&#40;0&#41;&#58; I2C device "CRTDDC_A&#58;ddc2" removed.
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "CRTDDC_A" removed.
&#40;II&#41; intel&#40;0&#41;&#58; EDID vendor "SRC", prod id 706
&#40;II&#41; intel&#40;0&#41;&#58; Using hsync ranges from config file
&#40;II&#41; intel&#40;0&#41;&#58; Using vrefresh ranges from config file
&#40;II&#41; intel&#40;0&#41;&#58; Printing DDC gathered Modelines&#58;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x400"x0.0   31.50  640 664 704 832  400 409 412 450 -hsync +vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   94.50  1024 1072 1168 1376  768 769 772 808 +hsync +vsync &#40;68.7 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync &#40;37.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 491 520 -hsync -vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   25.20  640 656 752 800  480 490 492 525 -hsync -vsync &#40;31.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync &#40;31.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   78.80  1024 1040 1136 1312  768 769 772 800 +hsync +vsync &#40;60.1 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync &#40;56.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync &#40;48.4 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync &#40;46.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync &#40;48.1 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1280x1024"x60.0  108.88  1280 1360 1496 1712  1024 1025 1028 1060 -hsync +vsync &#40;63.6 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; EDID vendor "SRC", prod id 706
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "CRTDDC_A" initialized.
&#40;II&#41; intel&#40;0&#41;&#58; I2C device "CRTDDC_A&#58;ddc2" registered at address 0xA0.
&#40;II&#41; intel&#40;0&#41;&#58; I2C device "CRTDDC_A&#58;ddc2" removed.
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "CRTDDC_A" removed.
&#40;II&#41; intel&#40;0&#41;&#58; EDID vendor "SRC", prod id 706
&#40;II&#41; intel&#40;0&#41;&#58; Using hsync ranges from config file
&#40;II&#41; intel&#40;0&#41;&#58; Using vrefresh ranges from config file
&#40;II&#41; intel&#40;0&#41;&#58; Printing DDC gathered Modelines&#58;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x400"x0.0   31.50  640 664 704 832  400 409 412 450 -hsync +vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   94.50  1024 1072 1168 1376  768 769 772 808 +hsync +vsync &#40;68.7 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync &#40;37.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 491 520 -hsync -vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   25.20  640 656 752 800  480 490 492 525 -hsync -vsync &#40;31.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync &#40;31.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   78.80  1024 1040 1136 1312  768 769 772 800 +hsync +vsync &#40;60.1 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync &#40;56.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync &#40;48.4 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync &#40;46.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync &#40;48.1 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1280x1024"x60.0  108.88  1280 1360 1496 1712  1024 1025 1028 1060 -hsync +vsync &#40;63.6 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; EDID vendor "SRC", prod id 706
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "CRTDDC_A" initialized.
&#40;II&#41; intel&#40;0&#41;&#58; I2C device "CRTDDC_A&#58;ddc2" registered at address 0xA0.
&#40;II&#41; intel&#40;0&#41;&#58; I2C device "CRTDDC_A&#58;ddc2" removed.
&#40;II&#41; intel&#40;0&#41;&#58; I2C bus "CRTDDC_A" removed.
&#40;II&#41; intel&#40;0&#41;&#58; EDID vendor "SRC", prod id 706
&#40;II&#41; intel&#40;0&#41;&#58; Using hsync ranges from config file
&#40;II&#41; intel&#40;0&#41;&#58; Using vrefresh ranges from config file
&#40;II&#41; intel&#40;0&#41;&#58; Printing DDC gathered Modelines&#58;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x400"x0.0   31.50  640 664 704 832  400 409 412 450 -hsync +vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   94.50  1024 1072 1168 1376  768 769 772 808 +hsync +vsync &#40;68.7 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync &#40;37.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 491 520 -hsync -vsync &#40;37.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "640x480"x0.0   25.20  640 656 752 800  480 490 492 525 -hsync -vsync &#40;31.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync &#40;31.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   78.80  1024 1040 1136 1312  768 769 772 800 +hsync +vsync &#40;60.1 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync &#40;56.5 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync &#40;48.4 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync &#40;46.9 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "800x600"x0.0   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync &#40;48.1 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; Modeline "1280x1024"x60.0  108.88  1280 1360 1496 1712  1024 1025 1028 1060 -hsync +vsync &#40;63.6 kHz&#41;
&#40;II&#41; intel&#40;0&#41;&#58; EDID vendor "SRC", prod id 706
danke

User avatar
Janka
Posts: 3585
Joined: 11. Feb 2006 19:10

#14 Post by Janka »

Sieht immer noch nicht vollständig aus. Aber ok.

Grundproblem scheint diese Stelle zu sein:

Code: Select all

&#40;EE&#41; Screen Screen&#91;0&#93; doesn't exist&#58; deleting placement 
Da stimmt irgendwas mit dem ServerLayout nicht. Du brauchst beide folgenden Zeilen:

Code: Select all

Screen "Screen&#91;0&#93;"
Screen "Screen&#91;TV&#93;" rightof "Screen&#91;0&#93;"
Weiter unten kommt ein wenig mehr Info, woran du den bisher fehlenden Erfolg der Bastelei leicht erkennen kannst:

Code: Select all

&#40;II&#41; intel&#40;0&#41;&#58; Output configuration&#58; 
 &#40;II&#41; intel&#40;0&#41;&#58;   Pipe A is on 
 &#40;II&#41; intel&#40;0&#41;&#58;   Display plane A is now enabled and connected to pipe A. 
 &#40;II&#41; intel&#40;0&#41;&#58;   Pipe B is off 
 &#40;II&#41; intel&#40;0&#41;&#58;   Display plane B is now disabled and connected to pipe B. 
 &#40;II&#41; intel&#40;0&#41;&#58;   Output VGA is connected to pipe A 
 &#40;II&#41; intel&#40;0&#41;&#58;   Output TV-1 is connected to pipe none
Die Intel-Grafikchips haben zwei Display-Pipes, A und B. Sie können also zwei verschiedene Bilder darstellen. Jede der beiden Pipes kann man auf einen oder mehrere der vorhandenen Ausgänge aufschalten. Hier meckert er über zwei Dinge: Pipe B ist aus und TV-1 ist mit keiner Pipe verbunden. Daher kein Bild. Daran müssen wir evtl. dann auch noch rumstellen.

Pipe B ist übrigens bei den Intel-Grafikchips WIMRE immer ohne Beschleunigung. Da sollte also der Monitor mit der kleineren Auflösung dranhängen.

Janka
Ich vertonne Spam immer in /dev/dsp statt /dev/null.
Ich mag die Schreie.

inixlinux

#15 Post by inixlinux »

duch hinzufügen von

Code: Select all

Screen "Screen&#91;0&#93;"
erscheint nun folgender Fehler nicht mehr

Code: Select all

&#40;EE&#41; Screen Screen&#91;0&#93; doesn't exist&#58; deleting placement 
jedoch steht bei Pipe B immer noch none.

Wie aktiviere ich diese.

danke

Post Reply