Hinweis: Das Forum wird geschlossen! Neue Registrierungen sind nicht mehr möglich!

 Zurück zu Pro-Linux   Foren-Übersicht   FAQ     Suchen    Mitgliederliste
Problemme mit Hylafax und Us Robotics Sportster Flash Modem!!!

 
Neuen Beitrag schreiben   Auf Beitrag antworten    Pro-Linux Foren-Übersicht -> Netzwerk
Vorheriges Thema anzeigen :: Nächstes Thema anzeigen  
Autor Nachricht
Maik
Gast





BeitragVerfasst am: 28. Apr 2002 20:16   Titel: Problemme mit Hylafax und Us Robotics Sportster Flash Modem!!!

hi,

hab gestern bei mir hylafax instaliert es left gut bis auf einz
ich kann faxe senden ohne Problemme aber emfangen kann ich es nicht ich
krieg jedes mal
kein Fax und folgende email:
Das ganze ist unter Woody Debian instaliert. Hab ein
Us Robotics Sportster Flash Modem

Woran kann das liegen!
---
An attempt to receive facsimile on ttyS0 failed because:

RSPREC invalid response received

---- Transcript of session follows ----

Apr 28 20:07:16.95: [ 1952]: SESSION BEGIN 00000026 4988989800
Apr 28 20:07:16.95: [ 1952]: HylaFAX (tm) Version 4.1.1
Apr 28 20:07:16.95: [ 1952]: <-- [4:ATA®]
Apr 28 20:07:23.16: [ 1952]: --> [4:+FCO]
Apr 28 20:07:23.16: [ 1952]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS0'
Apr 28 20:07:23.16: [ 1952]: MODEM input buffering enabled
Apr 28 20:07:23.16: [ 1952]: RECV FAX: begin
Apr 28 20:07:25.01: [ 1952]: --> [27:+FTI:"+49 2561 959-282697 "]
Apr 28 20:07:25.01: [ 1952]: REMOTE TSI "+49 2561 959-282697"
Apr 28 20:07:25.01: [ 1952]: --> [20:+FCS:1,3,0,0,0,0,0,0]
Apr 28 20:07:25.01: [ 1952]: REMOTE wants 9600 bit/s
Apr 28 20:07:25.01: [ 1952]: REMOTE wants page width 1728 pixels in 215 mm
Apr 28 20:07:25.01: [ 1952]: REMOTE wants A4 page length (297 mm)
Apr 28 20:07:25.01: [ 1952]: REMOTE wants 7.7 line/mm
Apr 28 20:07:25.01: [ 1952]: REMOTE wants 1-D MR
Apr 28 20:07:25.01: [ 1952]: --> [2:OK]
Apr 28 20:07:25.01: [ 1952]: <-- [7:AT+FDR®]
Apr 28 20:07:30.25: [ 1952]: --> [27:+FTI:"+49 2561 959-282697 "]
Apr 28 20:07:30.25: [ 1952]: REMOTE TSI "+49 2561 959-282697"
Apr 28 20:07:30.25: [ 1952]: --> [20:+FCS:1,2,0,0,0,0,0,0]
Apr 28 20:07:30.25: [ 1952]: REMOTE wants 7200 bit/s
Apr 28 20:07:30.25: [ 1952]: REMOTE wants page width 1728 pixels in 215 mm
Apr 28 20:07:30.25: [ 1952]: REMOTE wants A4 page length (297 mm)
Apr 28 20:07:30.25: [ 1952]: REMOTE wants 7.7 line/mm
Apr 28 20:07:30.25: [ 1952]: REMOTE wants 1-D MR
Apr 28 20:07:34.02: [ 1952]: --> [7:CONNECT]
Apr 28 20:07:34.02: [ 1952]: RECV: begin page
Apr 28 20:07:34.02: [ 1952]: RECV: send trigger 022
Apr 28 20:07:36.61: [ 1952]: RECV: 170 total lines, 5 bad lines, 4
consecutive bad lines
Apr 28 20:07:36.61: [ 1952]: --> [16:+FPS:1,171,0,0,0]
Apr 28 20:07:45.95: [ 1952]: --> [7:+FHS:A1]
Apr 28 20:07:45.95: [ 1952]: REMOTE HANGUP: RSPREC invalid response received
(code A1)
Apr 28 20:07:46.08: [ 1952]: --> [2:OK]
Apr 28 20:07:46.08: [ 1952]: RECV FAX (00000026): recvq/fax00021.tif from
+49 2561 959-282697, route to <unspecified>, 0
pages in 0:23
Apr 28 20:07:46.08: [ 1952]: RECV FAX: RSPREC invalid response received
Apr 28 20:07:46.09: [ 1952]: RECV FAX (00000026): session with +49 2561
959-282697 terminated abnormally: RSPREC invalid
response received
Apr 28 20:07:46.09: [ 1952]: RECV FAX: bin/faxrcvd "recvq/fax00021.tif"
"ttyS0" "00000026" "RSPREC invalid response
received" "" ""
--------------------------

hier ist auch mein Config:

#
CountryCode: 49
AreaCode: 2001
FAXNumber: +49.2001.203.003
LongDistancePrefix: 0
InternationalPrefix: 00
DialStringRules: etc/dialrules
ServerTracing: 527
SessionTracing: 527
RecvFileMode: 0644
LogFileMode: 0777
DeviceMode: 0666
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-r -b -s %s %l"
LocalIdentifier: "cobra"
LogFacility: daemon
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxRecvPages: 30
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class2.0 # use class 2.0 interface
ModemRate: 38400 # DCE-DTE communication rate
ModemFlowControl: rtscts # XON/XOFF flow control assumed
#
ModemNoFlowCmd: AT&H0&I0&R1 # setup modem for no flow control
ModemHardFlowCmd: AT&H1&I0&R2 # setup modem for hardware flow control
ModemSoftFlowCmd: AT&H2&I2&R1 # setup modem for software flow control
#
ModemSetupDTRCmd: ATS13=1&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not)
ModemResultCodesCmd: ATQ0X4 # enable extended result codes
#
# NB: adaptive answer only seems to work properly when
# the modem is left idling in Class 2.0
#
ModemSetupAACmd: AT+FAA=1
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd: "ATM0 ATM1 ATM1 ATM1 ATM1"
#
# Modem does not support HDLC frame tracing; we add this just
# to eliminate spurious ERROR results that confuse the naive.
#
Class2BUGCmd: AT+FBU=0
#
# The modem doesn't support copy quality checking, even though it
# returns (0-2,0-2) for AT+FCQ=?; therefore we override the query
# response so that the server will do copy quality checking.
#
Class2CQQueryCmd: !(0),(0) # override modem response
#
# Disables the reporting of bad frames by the modem. This
# overcomes a firmware problem in the x2 and V90 Sportsters.
# It is not necessary for the Courier modem.
#
Class2NRCmd: AT+FNR=1,1,1,0
#
# USR modems violate Class 2.0 specs and do not send RTC itself
#
Class2SendRTC: yes
#
# +FAP=? not supported on this modem, gives ERROR in ServerTracing
#
Class2APQueryCmd: none
 

Beiträge vom vorherigen Thema anzeigen:   
     Pro-Linux Foren-Übersicht -> Netzwerk Alle Zeiten sind GMT + 1 Stunde
Seite 1 von 1

 
Gehen Sie zu:  

Powered by phpBB © phpBB Group
pro_linux Theme © 2004 by Mandaxy