PCI Modem unter Suse Linux 8.0

[mathabu]

Hallo,

Ich habe Problemm bei der Installation von Rockwell 56k PCI Modem.
bei dem Befehl setserial weiss ich nicht , welche I/O Adresse von dem PCI Modem hat.
Kann jemand mir sagen, wie ich diese heraus finden kann, mit 0x220 funzs nicht !

Danke !

lspci -v

linux:~ # lspci -v
00:00.0 Host bridge: VIA Technologies, Inc. VT8367 [KT266]
Flags: bus master, medium devsel, latency 8
Memory at e8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Capabilities: [c0] Power Management version 2

00:01.0 PCI bridge: VIA Technologies, Inc. VT8367 [KT266 AGP] (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: ec000000-edffffff
Prefetchable memory behind bridge: e0000000-e7ffffff
Capabilities: [80] Power Management version 2

00:09.0 Multimedia audio controller: Ensoniq ES1371 [AudioPCI-97] (rev 06)
Subsystem: Ensoniq Creative Sound Blaster AudioPCI64V, AudioPCI128
Flags: bus master, slow devsel, latency 32, IRQ 11
I/O ports at d000
Capabilities: [dc] Power Management version 1

00:0a.0 Multimedia video controller: Brooktree Corporation Bt848 TV with DMA push (rev 12)
Flags: bus master, medium devsel, latency 32, IRQ 11
Memory at ee011000 (32-bit, prefetchable) [size=4K]

00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139 (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Flags: bus master, medium devsel, latency 32, IRQ 11
I/O ports at d400 [size=256]
Memory at ee010000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2

00:0c.0 Serial controller: Rockwell International HCF 56k Data/Fax/Voice Modem (rev 01) (prog-if 00 [8250])
Subsystem: Askey Computer Corp.: Unknown device 1009
Flags: bus master, medium devsel, latency 32, IRQ 10
Memory at ee000000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [40] Power Management version 1

00:11.0 ISA bridge: VIA Technologies, Inc. VT8233 PCI to ISA Bridge
Subsystem: VIA Technologies, Inc.: Unknown device 0000
Flags: bus master, stepping, medium devsel, latency 0
Capabilities: [c0] Power Management version 2

00:11.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. Bus Master IDE
Flags: bus master, medium devsel, latency 32
I/O ports at d800
Capabilities: [c0] Power Management version 2

00:11.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 1b) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Flags: bus master, medium devsel, latency 32, IRQ 11
I/O ports at dc00
Capabilities: [80] Power Management version 2

00:11.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 1b) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Flags: bus master, medium devsel, latency 32, IRQ 11
I/O ports at e000
Capabilities: [80] Power Management version 2

00:11.4 USB Controller: VIA Technologies, Inc. UHCI USB (rev 1b) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Flags: bus master, medium devsel, latency 32, IRQ 11
I/O ports at e400
Capabilities: [80] Power Management version 2

01:00.0 VGA compatible controller: nVidia Corporation NV11 (GeForce2 MX DDR) (rev b2) (prog-if 00 [VGA])
Subsystem: Elsa AG: Unknown device 0c6a
Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 10
Memory at ec000000 (32-bit, non-prefetchable)
Memory at e0000000 (32-bit, prefetchable)
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [60] Power Management version 2
Capabilities: [44] AGP version 2.0



Oct 25 00:22:56 linux kernel: I/O error: dev 08:00, sector 0
Oct 25 00:22:56 linux kernel: unable to read partition table
Oct 25 00:22:56 linux kernel: sda : READ CAPACITY failed.
Oct 25 00:22:56 linux Oct 25 00:22:56 linux

[ratte]

wie kommste denn auf die vermutung, dass es 0x220 sein koennte?

ratte

[mathabu]

Ich habe es einfach nur ausprobiert. <img src="http://www.pl-forum.de/UltraBoard/Images/Happy.gif" border="0" align="middle"> die IRQ ist ja 10, und "Memory at ee000000" ???? weiss ich nicht.
Da kommt diese Fehlermeldung von der Console.
Was muss ich genauer machen ? Ich habe einen Treiber von Connexian PCI Modem für Linux im Internet gefunden. Aber es sind nur laute *.o dateien. Ich weiss nicht ob das der richtiger Treiber ist und wie man diesen installieren !
Kannst Du mir vielleicht weiterhelfen ? Danke im Voraus !

Gruss